Ford Falcon. Manual — part 482
501-20b-143
Occupant Restraints — Passive
501-20b-143
REMOVAL AND INSTALLATION (Continued)
Driver Airbag Module
WARNING: Never probe the connectors on
the side airbag module. Doing so can result in
Special Tool(s)
side airbag deployment.
Diagnostic Tool, Restraint
WARNING: Vehicle sensor orientation is
System (2 req’d)
critical for proper system operation. If a vehicle
418-F395 (014-R1079)
equipped with an airbag supplemental restraint
system (SRS) is involved in a collision, inspect
the sensor mounting bracket and wiring pigtail for
deformation. Replace and properly position the
sensor or any other damaged supplemental
Diagnostic Tool, Restraint
restraint system (SRS) components whether or
System (4 req’d)
not the airbag is deployed.
418-F403
WARNING: The restraint system diagnostic
tool is for restraint system service only. Remove
from vehicle prior to road use. Failure to remove
could result in injury and possible violation of
vehicle safety standards.
Diagnostic Tool, Restraint
System (2 req’d)
WARNING: To avoid accidental deployment
418-F088 (105-R0012)
and possible personal injury, the backup power
supply must be depleted before repairing or
replacing any front or side airbag supplemental
restraint system (SRS) components and before
servicing, replacing, adjusting or striking
components near the front or side airbag sensors,
Removal
such as doors, instrument panel, console, door
latches, strikers, seats and hood latches.
WARNING: Always wear safety glasses when
The side impact sensors (if equipped) are located
repairing an airbag supplemental restraint system
at or near the base of the B-pillars and C-pillars.
(SRS) vehicle and when handling an airbag
To deplete the backup power supply energy,
module. This will reduce the risk of injury in the
disconnect the battery ground cable and wait at
event of an accidental deployment.
least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
WARNING: Carry a live airbag module with
NOTE: If a seat equipped with a seat mounted side
the airbag and trim cover pointed away from your
airbag and/or a safety belt pretensioner (if equipped)
body. This will reduce the risk of injury in the
system is being serviced, the airbag system must
event of an accidental deployment.
be deactivated.
WARNING: Do not set a live airbag module
NOTE: Restraint system diagnostic tools MUST be
down with the trim cover face down. This will
installed under the seats in the seat side airbag (if
reduce the risk of injury in the event of an
equipped) and safety belt pretensioner.
accidental deployment.
NOTE: Diagnostics or repairs are not to be performed
on a seat equipped with a seat side airbag with the
WARNING: After deployment, the airbag
seat in the vehicle. Prior to attempting to diagnose or
surface can contain deposits of sodium
repair a seat concern when equipped with a seat side
hydroxide, a product of the gas generant
airbag, the seat must be removed from the vehicle
combustion that is irritating to the skin. Wash
and the restraint system diagnostic tools must be
your hands with soap and water afterwards.
installed in the seat side airbag electrical connectors.
The restraint system diagnostic tools must be
WARNING: Never probe the connectors on
removed prior to operating the vehicle over the
the airbag module. Doing so can result in airbag
road.
deployment, which can result in personal injury.
NOTE: After diagnosing or repairing an SRS, the
WARNING: The safety belt buckle
restraint system diagnostic tools must be
pretensioner is a pyrotechnic device. Never probe removed before operating the vehicle over the
a pretensioner electrical connector. Doing so
road.
could result in pretensioner or airbag deployment
NOTE: After diagnosing or repairing a seat system,
and could result in personal injury.
the restraint system diagnostic tools must be
G12363 en
501-20b-144
Occupant Restraints — Passive
501-20b-144
REMOVAL AND INSTALLATION (Continued)
removed before operating the vehicle over the
Item
Description
road.
3
Steering wheel audio controls connector
NOTE: The SRS must be fully operational and free of 5. Attach the restraint system diagnostic tools to the
faults before releasing the vehicle to the customer.
clockspring electrical connectors at the top of the
steering column.
1. Disconnect the battery ground cable and wait at
least one minute. For additional information, refer
to Section 414-01.
2. Remove the two steering wheel back cover plugs.
3. Remove the two driver airbag module bolts (one
shown).
6. Push in on the glove compartment sides,
releasing the stops and lowering it out of the way.
4. Remove the driver airbag module.
1. Release the two retaining tabs. Disconnect
the driver airbag module electrical connector.
Label the driver airbag module squib
number on the driver airbag module
electrical connector before disconnecting.
2. Release the two retaining tabs. Disconnect
the driver airbag module electrical connector.
Label the driver airbag module squib
number on the driver airbag module
electrical connector before disconnecting.
7. Through the glove compartment opening, release
3. Disconnect the horn switch electrical
the tab and disconnect the passenger airbag
connector.
module electrical connector.
4. Remove the driver airbag module.
Item
Description
1
Clokspring LH connector
2
Clokspring RH connector
G12363 en
501-20b-145
Occupant Restraints — Passive
501-20b-145
REMOVAL AND INSTALLATION (Continued)
8. Attach the restraint system diagnostic tool to the
3. Attach the restraint system diagnostic tool to the
vehicle harness side of the passenger airbag
front RH seat safety belt buckle pretensioner floor
module electrical connector.
electrical connector.
Vehicles with power seats
4. Attach the restraint system diagnostic tool to the
vehicle harness side of the LH side air curtain
electrical connector.
WARNING: To avoid accidental deployment
5. From under the front LH seat, push in to release
and possible personal injury, the backup power
the tab and disconnect the safety belt buckle
supply must be depleted before repairing or
pretensioner electrical connector.
replacing any front or side airbag supplemental
restraint system (SRS) components and before
servicing, replacing, adjusting or striking
components near the front or side airbag sensors,
such as doors, instrument panel, console, door
latches, strikers, seats and hood latches.
The side impact sensors (if equipped) are located
at or near the base of the B-pillars.
To deplete the backup power supply energy,
disconnect the battery ground cable and wait at
least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
1. Vehicles with power seats, disconnect the battery
ground cable and wait at least one minute. For
additional information, refer to Section 414-01.
2. From under the front RH seat, push in to release
6. Attach the restraint system diagnostic tool to the
the tab and disconnect the safety belt buckle
front LH seat safety belt buckle pretensioner floor
pretensioner electrical connector.
electrical connector.
7. Connect the battery ground cable. For additional
information, refer to Section 414-01.
G12363 en
501-20b-146
Occupant Restraints — Passive
501-20b-146
REMOVAL AND INSTALLATION (Continued)
8. With the restraint system diagnostic tools installed
at all deployable devices, prove out the
supplemental restraint system (SRS). For
additional information, refer to Airbag and Safety
Belt Pretensioner Supplemental Restraint System
(SRS) in this section.
9. Disconnect the battery ground cable and wait at
least one minute. For additional information, refer
to Section 414-01.
Installation
WARNING: To reduce the risk of serious
personal injury, read and follow all warnings,
cautions, and notes at the beginning of the
deactivation procedure.
Item
Description
Vehicles with power seats
1
Clokspring LH connector
1. For vehicles with power seats, connect the battery
2
Clokspring RH connector
ground cable. For additional information, refer to
Section 414-01.
3
Steering wheel audio controls connector
2. Position the front seats rearward.
6. Install the two driver airbag module bolts (one
3. Disconnect the battery ground cable and wait at
shown).
least one minute. For additional information, refer
to Section 414-01.
4. Remove the restraint system diagnostic tools from
the clockspring electrical connector at the top of
the steering column.
7. Install the two steering wheel back cover plugs.
8. Connect the battery ground cable. For additional
information, refer to Section 414-01.
WARNING: The restraint system diagnostic
5. Position the driver airbag module to the steering
tool is for restraint system service only. Remove
wheel.
from vehicle prior to road use. Failure to remove
could result in injury and possible violation of
1. Connect the horn switch electrical connector.
vehicle safety standards.
CAUTION: The clockspring electrical
9. With the restraint system diagnostic tools still
connectors are unique and cannot be
installed at the remaining deployable devices,
reversed when connected to the driver
prove out the supplemental restraint system
airbag module. Match the electrical
(SRS). For additional information, refer to Airbag
connector key to the keyway in the driver
and Safety Belt Pretensioner Supplemental
airbag module. Do not force the electrical
Restraint System (SRS) in the Diagnosis and
connectors into the driver airbag module.
Testing portion of this section.
2. Connect the driver airbag module electrical
WARNING: To avoid accidental
connectors as noted during removal.
deployment and possible personal injury, the
3. Position the driver airbag module to the
backup power supply must be depleted before
steering wheel.
repairing or replacing any front or side airbag
supplemental restraint system (SRS)
components and before servicing, replacing,
G12363 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст