Ford Falcon. Manual — part 485
501-20b-155
Occupant Restraints — Passive
501-20b-155
REMOVAL AND INSTALLATION (Continued)
NOTE: Repair is made by installing a new part only. If
Side Airbag Bridge Resistor
the new part does not correct the condition, install the
original part and carry out the diagnostic procedure
Special Tool(s)
again.
Diagnostic Tool, Restraint
1. Disconnect the battery ground cable (14301) and
System (2 req’d)
wait at least one minute. For additional
418-F395 (014-R1079)
information, refer to Section 414-01.
WARNING: To reduce the risk of serious
personal injury, read and follow all warnings,
notes, and instructions in the supplemental
restraint system (SRS) deactivation /
Diagnostic Tool, Restraint
reactivation procedure.
System (4 req’d)
2. Deactivate the supplemental restraint system
418-F403
(SRS). For additional information, refer to
Supplemental Restraint System (SRS)
Deactivation and Reactivation in the General
Procedures portion of this section.
Installation
Diagnostic Tool, Restraint
System (2 req’d)
WARNING: To avoid accidental deployment
418-F088 (105-R0012)
and possible personal injury, the backup power
supply must be depleted before repairing or
replacing any front or side airbag supplemental
restraint system (SRS) components and before
servicing, replacing, adjusting or striking
components near the front or side airbag sensors,
Removal
such as doors, instrument panel, console, door
latches, strikers, seats and hood latches.
WARNING: Always wear safety glasses when The side impact sensors (if equipped) are located
repairing an airbag supplemental restraint system at or near the base of the B-pillars and C-pillars.
(SRS) vehicle and when handling an airbag
To deplete the backup power supply energy,
module. This will reduce the risk of injury in the
disconnect the battery ground cable and wait at
event of an accidental deployment.
least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
WARNING: Never probe the connectors on
1. Disconnect the battery ground cable (14301) and
the airbag module. Doing so can result in airbag
wait at least one minute. For additional
deployment, which can result in personal injury.
information, refer to Section 414-01.
WARNING: To avoid accidental deployment
WARNING: The restraint system
and possible personal injury, the backup power
diagnostic tool is for restraint system service
supply must be depleted before repairing or
only. Remove from the vehicle prior to road
replacing any front or side airbag supplemental
use. Failure to remove could result in injury
restraint system (SRS) components and before
and possible violation of vehicle safety
servicing, replacing, adjusting or striking
standards.
components near the front or side airbag sensors,
2. With all the restraint system diagnostic tools
such as doors, instrument panel, console, door
removed, prove out the supplemental restraint
latches, strikers, seats and hood latches.
system (SRS). For additional information, refer to
The side impact sensors (if equipped) are located
Airbag and Safety Belt Pretensioner Supplemental
at or near the base of the B-pillars and C-pillars.
Restraint System (SRS) in the Diagnosis and
To deplete the backup power supply energy,
Testing portion of this section.
disconnect the battery ground cable and wait at
least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
G12366 en
501-20b-156
Occupant Restraints — Passive
501-20b-156
REMOVAL AND INSTALLATION (Continued)
1. Deactivate the supplemental restraint system
Seat Position Sensor
(SRS). For additional information, refer to
Supplemental Restraint System (SRS)
Special Tool(s)
Deactivation and Reactivation in the General
Diagnostic Tool, Restraint
Procedures portion of this section.
System (2 Req’d)
All vehicles
418-F403
WARNING: To reduce the risk of serious
personal injury, read and follow all warnings,
cautions, notes, and instructions in the seat
removal and installation procedure.
Diagnostic Tool, Restraint
System (2 req’d)
CAUTION: Use care when handling the seat
418-F088 (105-R0012)
and track assembly. Dropping the assembly or
sitting on a seat not secured in the vehicle can
result in damaged components.
1. Remove the driver seat. For additional
information, refer to Section 501-10.
Vehicles with power seats
Removal
1. Remove the seat position sensor.
All vehicles
WARNING: To avoid accidental deployment
and possible personal injury, the backup power
supply must be depleted before repairing or
replacing any front or side airbag supplemental
restraint system (SRS) components and before
servicing, replacing, adjusting or striking
components near the front or side airbag sensors,
such as doors, instrument panel, console, door
latches, strikers, seats and hood latches.
The side impact sensors (if equipped) are located
at or near the base of the B-pillars.
To deplete the backup power supply energy,
disconnect the battery ground cable and wait at
least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
Item
Description
1. Disconnect the battery ground cable (14301) and
1
Seat position sensor
wait at least one minute. For additional
2
Bolt hole
information, refer to Section 414-01.
3
Sensor Electrical connector
Vehicles with side airbags
1. Disconnect the electrical connector.
2. Remove the bolt.
WARNING: To reduce the risk of serious
personal injury, read and follow all warnings,
3. Press the sensor tab inward to release and
notes, and instructions in the supplemental
remove the sensor.
restraint system (SRS) deactivation/reactivation
procedure.
G12366 en
501-20b-157
Occupant Restraints — Passive
501-20b-157
REMOVAL AND INSTALLATION (Continued)
4. Remove the magnet assembly bolt.
could result in injury and possible violation of
vehicle safety standards.
5. Slide back and remove the magnet assembly.
1. With all the restraint system diagnostic tools
Vehicles with manual seat
removed, prove out the supplemental restraint
1. Remove the seat position sensor.
system (SRS). For additional information, refer to
Airbag and Safety Belt Pretensioner Supplemental
1. Disconnect the electrical connector.
Restraint System (SRS), in the Diagnosis and
2. Remove the bolt.
Testing portion of this section.
3. Remove the seat position sensor.
2. Check the active restraint system for correct
Installation
operation. For additional information, refer to
Vehicles with manual seat
Section 501-20A.
1. Install the seat position sensor.
Side Airbag Module
1. Position the seat position sensor.
Align the sensor locator clips to the seat
Special Tool(s)
alignment bracket.
Diagnostic Tool, Restraint
2. Install the bolt.
System (2 Req’d)
3. Connect the electrical connector.
418-F088 (105-R0012)
Vehicles with power seats
1. Install the seat position sensor.
1. Install the magnet assembly onto the pivot
and slide forward.
Removal
2. Install the bolt.
3. Position the sensor and engage the retaining
WARNING: Always wear safety glasses when
tab.
repairing an airbag supplemental restraint system
4. Install the bolt.
(SRS) vehicle and when handling an airbag
module. This will reduce the risk of injury in the
5. Connect the electrical connector.
event of an accidental deployment.
All vehicles
WARNING: Carry a live side airbag module
WARNING: To reduce the risk of serious
with the airbag and tear seam pointed away from
personal injury, read and follow all warnings,
your body. This will reduce the risk of injury in the
cautions, notes, and instructions in the seat
event of an accidental deployment.
removal and installation procedure.
NOTE: Make sure the battery ground cable is still
WARNING: Do not set a live side airbag
disconnected before proceeding with the installation
module down on the cover tear seam. This will
portion of this procedure.
reduce the risk of injury in the event of an
accidental deployment.
1. Install the driver seat into the vehicle. For
additional information, refer to Section 501-10.
WARNING: After deployment, the airbag
Vehicles with side airbags
surface can contain deposits of sodium
hydroxide, a product of the gas generant
combustion that is irritating to the skin. Wash
WARNING: To reduce the risk of serious
your hands with soap and water afterwards.
personal injury, read and follow all warnings,
notes, and instructions in the supplemental
restraint system (SRS) deactivation/reactivation
WARNING: Never probe the connectors on
procedure.
the airbag module. Doing so can result in airbag
deployment, which can result in personal injury.
1. Reactivate the supplemental restraint system
(SRS). For additional information, refer to
WARNING: Vehicle sensor orientation is
Supplemental Restraint System (SRS)
critical for proper system operation. If a vehicle
Deactivation and Reactivation in the General
equipped with an airbag supplemental restraint
Procedures portion of this section.
system (SRS) is involved in a collision, inspect
All vehicles
the sensor mounting bracket and wiring pigtail for
deformation. Replace and properly position the
WARNING: The restraint system diagnostic
sensor or any other damaged supplemental
tool is for restraint system service only. Remove
restraint system (SRS) components whether or
from vehicle prior to road use. Failure to remove
not the airbag is deployed.
G12369 en
501-20b-158
Occupant Restraints — Passive
501-20b-158
REMOVAL AND INSTALLATION (Continued)
NOTE: Diagnostics may be performed on seat
WARNING: To avoid accidental deployment
systems other than the side airbag or the safety belt
and possible personal injury, the backup power
pretensioner (if equipped) system (lumbar, climate
supply must be depleted before repairing or
controlled, heated, power seat track) with the seat
replacing any front or side airbag supplemental
installed in the vehicle as long as the restraint system
restraint system (SRS) components and before
diagnostic tools are installed under the seats in the
servicing, replacing, adjusting or striking
side airbag and safety belt pretensioner to floor
components near the front or side airbag sensors,
connectors.
such as doors, instrument panel, console, door
latches, strikers, seats and hood latches. Please
NOTE: After diagnosing/repairing a seat system the
refer to the appropriate vehicle shop manual to
restraint system diagnostic tools must be removed
determine location of the front airbag sensors.
before operating the vehicle over the road.
The side airbag sensors are located at or near the
NOTE: When replacing the side airbag after
base of the B-pillar. To deplete the backup power
deployment, refer to Section 501-10 for additional
supply energy, disconnect the battery ground
information concerning the installation of a new side
cable and wait at least one minute. Be sure to
airbag.
disconnect auxiliary batteries and power supplies
(if equipped).
NOTE: Repair is made by installing a new part only. If
the new part does not correct the condition, install the
WARNING: The restraint system diagnostic
original part and perform the diagnostic procedure
tool is for restraint system service only. Remove
again.
from vehicle prior to road use. Failure to remove
NOTE: The left-hand drive driver seat side airbag
could result in injury and possible violation of
removal is shown, all others are similar.
vehicle safety standards.
1. Remove the affected seat from the vehicle. For
WARNING: Never power up a seat inside or
additional information, refer to Section 501-10.
out of the vehicle except using the in-car
NOTE: Use care not to damage the center hole
connector dedicated to power supply.
plug.
2. Pry out and remove the seat cushion adjuster
WARNING: Wait at least one minute after
handle center plug.
disconnecting the battery ground cable before
disconnecting any supplemantal restraint system
3. Remove the seat cushion adjuster handle.
electrical connector. Failure to follow this warning
1. Release the retaining tabs.
could cause premature deployment and may
2. Pull and remove the seat cushion adjuster
result in personal injury.
handle.
CAUTION: Use care when handling the seat
4. Remove the plastic outboard side cover.
and track assembly. Dropping the assembly or
1. Remove reclining knob.
sitting on a seat not secured in the vehicle may
2. Remove the 2 screw.
result in damaged components.
3. Pull out to release the retaining clips and
NOTE: If a seat equipped with a seat mounted side
remove the seat cushion side shield.
airbag and/or a safety belt pretensioner (if equipped)
If equipped, disconnect the power seat
system is being serviced the airbag system must be
switch electrical connector.
deactivated. Refer to Airbag and Safety Belt
Pretensioner Supplemental Restraint System (SRS),
in the Diagnosis and Testing portion of this section.
NOTE: Restraint system diagnostic tools MUST be
installed under the seats in the side airbag and safety
belt pretensioner.
NOTE: Diagnostics or repairs are not to be performed
on a side airbag system and/or a safety belt
pretensioner (if equipped) system with the seats in the
vehicle. Prior to attempting to diagnose/repair the side
airbag system and/or a safety belt pretensioner (if
equipped) system the seats must be removed from
the vehicle and the restraint system diagnostic tools
must be installed in the side airbag and the safety belt
pretensioner (if equipped) connectors. The restraint
4. Where applicable, disconnect plugs from
system diagnostic tools must be removed prior to
switch and/or memory buttons.
operating the vehicle over the road.
G12369 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст