Ford Falcon. Manual — part 345
413-08-23 Interior
Command
Centre 413-08-23
REMOVAL AND INSTALLATION (Continued)
4. Disconnect the remaining black connector from
Service Body Computer (BEM)
Body Computer.
Removal
NOTE: The 6 CD Audio Mechanism for Mid and High
Premium Sound Audio is very fragile. At no stage can
the Audio Module cannot be shocked or excessively
vibrated, especially when rotated beyond 90 degrees.
If the Audio Module is shocked or excessively vibrated
at any stage during removal, service or transport, the
Audio warranty is voided.
1. To access the Body Computer, place the ICC on
its side on a clean surface to prevent damage to
the Class A surface.
2. Remove 4 X M5 screws used to hold the Body
Computer to the Audio module.
5. Disconnect the antenna wire from the Audio
Module and remove Body Computer together with
the antenna cable.
3. If fitted with Satellite Navigation (TFT Screen
connection), remove 2 X M3 screws to separate
connector holder from Body Computer.
6. If only the Body Computer is to be serviced,
remove the antenna cable from the Body
Computer, and retain the antenna cable with the
vehicle.
NOTE: If only the Body Computer is to be
returned, ensure that the original Antenna
Leadwire remains with the vehicle & is fitted to the
replacement Body Computer.
If only the ICC is to be returned, ensure that both
the original Body Computer and original Antenna
Leadwire remain with the vehicle.
Replacement Body Computers are NOT be
supplied with Antenna Leadwires. Serviced ICC’s
are NOT supplied with Body Computers OR
Antenna Leadwires.
G86739 en
413-08-24 Interior
Command
Centre 413-08-24
REMOVAL AND INSTALLATION (Continued)
7. Disconnect the remaining black connector from
3. If fitted with TFT Screen connection, locate
Body Computer. Disconnect the antenna wire
connector holder and tighten 2 X M3 screws to
from the Audio Module and remove Body
0.6 Nm.
Computer together with the antenna cable.
4. Position Body Computer as shown on Audio
Installation
Module.
NOTE: The 6 CD Audio Mechanism for Mid and High 5. Tighten 4 X M5 screws to 1.0 Nm.
Premium Sound Audio is very fragile. At no stage can
the Audio Module cannot be shocked or excessively
vibrated, especially when rotated beyond 90 degrees.
If the Audio Module is shocked or excessively vibrated
at any stage during removal, service or transport, the
Audio warranty is voided.
1. To install the Body Computer, place the ICC on its
side on a clean surface to prevent damage to the
Class A surface.
2. Connect black connector to Body Computer.
6. As appropriate, clip or screw the Antenna Cable
to the Body Computer using M3 screw tightened
to 0.6 Nm.
7. If BEM has been replaced, after ICC is fitted to
vehicle, the BEM must be retrained to vehicle
using procedure as defined in BEM section (Refer
to section 419-10).
G86739 en
413-08-25 Interior
Command
Centre 413-08-25
REMOVAL AND INSTALLATION (Continued)
Service Remote Key Receiver (RKR)
Installation
1. Connect the RKR connector.
Removal
1. Remove 2 X M3 screws used to hold RKR to the
Air Register.
2. Position RKR on Air Register.
2. Remove
RKR.
3. Tighten 2 X M3 screws to 0.5 Nm.
3. Disconnect the RKR connector.
Service Air Register
1. Remove the ICC, as described earlier in this
section.
2. Remove the Remote Key Receiver. Refer to
Service Remote Key Receiver in this section
G86742 en
413-08-26 Interior
Command
Centre 413-08-26
REMOVAL AND INSTALLATION (Continued)
3. Remove wire harness from Air Register.
Installation
1. Position
Air
Register.
4. Remove 3 X M5 screws from Air Register.
2. Tighten 3 X M5 screws to 1.5 Nm, top centre
screw first.
5. Remove
Air
Register.
3. Reposition wire harness to Air Register.
4. Install the Remote Key Receiver. Refer to Service
Remote Key Receiver in this section.
Cabin Temperature Sensor
The Cabin Temperature Sensor is a non servicable
component and if faulty, the entire ICC unit as a
whole should be replaced after obtaining FCSD
approval.
G86742 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст