Ford Falcon. Manual — part 85
206-09-29
Anti Lock Control
206-09-29
REMOVAL AND INSTALLATION (Continued)
3. Unclip ABS Sensor cable clips from the leaf
3. Remove ABS Sensor retaining bolt.
spring (3 off).
4. Remove
ABS
Sensor.
4. Remove ABS sensor retaining bolt and withdraw
Installation
the ABS Sensor.
1. Installation is the reverse order to removal.
Rear Tone Wheel
The rear tone wheel is not separately serviceable.
The tone wheel is serviced with the complete half
shaft assembly.
Front Tone Wheel
The front hub tone wheel is not separately
serviceable. The tone wheel is serviced with the
complete hub assembly.
ABS Modulator Assembly
Removal
Installation
NOTE: The ABS Modulator Assembly is a critical
1. Installation is the reverse order to removal.
safety item. It should only be installed by trained and
experienced ABS Technicians.
Front ABS Wheel Sensors
1. Ensure ignition is in the off position.
Removal
2. Disconnect wiring from modulator by sliding the
1. Disconnect ABS Sensor cable.
locking slide pin out and lifting the connector from
2. Unclip fir tree clip 2 places.
the modulator.
G23427 en
206-09-30
Anti Lock Control
206-09-30
REMOVAL AND INSTALLATION (Continued)
3. Loosen the brake lines.
3. Refit mounting nuts and torque to specifications.
4. Loosen the 2 mounting nuts and withdraw the
4. Torque brake lines to specifications.
modulator from the vehicle.
5. Re-connect wiring by placing the connector on the
Installation
locating lugs of the ABS ECU and then pushing in
the locking slide to secure the connector.
1. Ensure mounting dampers are in place.
2. Position modulator ensuring fully seated in bottom
pin and hand thread to brake lines.
6. Bleed braking system as described in section
206-00 Brake System-General Information.
G23427 en
211-00-1
Steering System — General Information
211-00-1
SECTION : 211-00 Steering System — General
Information
VEHICLE APPLICATION : 2003.0 BA Falcon
CONTENTS
PAGE
DESCRIPTION AND OPERATION
Service Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211-00-2
GENERAL PROCEDURES
Power Steering System Bleeding Air . . . . . . . . . . . . . . . . . . . . . .211-00-3
Rack and Pinion Gear Rack Bearing Preload Adjustment . . . . . . . . . . . . . 211-00-4
Steering Gear Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . ..211-00-4
DISASSEMBLY AND ASSEMBLY
Steering System Exploded . . . . . . . . . . . . . . . . . . . . . . . . . .211-00-5
211-00-2
Steering System — General Information
211-00-2
DESCRIPTION AND OPERATION
Service Kits
Service Kit Contents Outer Tie Rod Assembly
Service Kit 26092580
Outer Tie Rod Assembly
Inner Tie Rod Assembly Service Kit 26092849
Inner Tie Rod Assembly
Metric Hex Nut
Seal Retaining Clamp
Rack And Pinion Boot Service Kit 26092851
Rack And Pinion Boot
Seal Retaining Clamp
Tie Rod End Clamp
Service Kit Grease (Not Shown)
Seal Installation Instruction Sheet (Not Shown)
Seal And Bearing Service Kit 26102901
Retaining Ring
Spool Shaft Seal
Needle And Bearing Assembly
Valve Body Ring (4)
Metric Hex Nut
Dust Cover
Adjuster Plug
Lube Shaft And Seal Instruction Sheet (Not
Shown)
Service Kit Grease (Not Shown)
Cylinder Line Assembly Service Kit (Right)
26102902
Cylinder Line Assembly
O-Ring Seal
Cylinder Line Assembly Service Kit (Left)
26102903
Cylinder Line Assembly
O-Ring Seal
Sleeve And Bushing Service Kit 26103515
Steering Gear Bushing
Steering Gear Bushing Sleeve
NOTE: Kits in bold reflect service kits supplied by
Delphi Saginaw. Parts listed below service kits are
included in each kit.
G27360 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст