Ford Aerostar (1997 year). Manual — part 13
49
Electronic Stereo and Stereo
Cassette Radios
Using the Controls on Your New Radio
How to tune radio stations (Stereo Radio)
There are three ways for you to tune in to a
particular station. You can manually locate the
station by using the “TUNE” button, “SEEK” the
station or select the station by using the memory
preset buttons, which you can set to any desired
frequency.
How to tune radio stations (Stereo Cassette
Radio)
There are five ways for you to tune in to a
particular station. You can manually locate the
station by using the “Tune” button, Automatic
Music Search (“AMS”), “SEEK” the station,
“SCAN” to the station or select the station by
using the memory preset buttons, which you can
set to any desired frequency.
❑
Using the “TUNE” function (Stereo Radio)
You can change the frequency up or down
one increment at a time by pressing and
releasing either the right (+) or left (
S
) side
of the “TUNE” button. To change frequencies
quickly, press and hold down either the right
or left side of the “TUNE” button.
Manual tuning adjusts your radio to any
allowable broadcast frequency, whether or
not a station is present on that frequency.
(See
All About Radio Frequencies
in this
section.)
50
❑
Using the “AMS” function to manually tune
your radio (Stereo Cassette Radio)
You can change the frequency up or down
one increment at a time by first pressing the
“AMS” button (display shows “TUNE”) then
within approximately five seconds pressing
and releasing either the right (
a
) or left (
b
)
side of the “SEEK” button. To change
frequencies quickly, press and
hold down
either the right or left side of the “SEEK”
button.
❑
Using the “SEEK” function
Press the right (
a
) side of the “SEEK”
button to select the next listenable station up
the frequency band. Press the left (
b
) side of
the button to select the next listenable station
down the frequency band. By holding the
button down, listenable stations can be
passed over to reach the desired station.
❑
Using the “SCAN” function (Stereo Cassette
Radio)
Press the “SCAN” button to enter the scan
mode. The radio will begin scanning up the
frequency band, stopping on each listenable
station for approximately a five-second
sampling. This continues until you press the
“SCAN” button a second time.
❑
Setting the Station Memory Preset buttons
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
FM stations (5 in FM1 and 5 in FM2). Follow
the easy steps below to set these buttons to
the desired frequencies.
51
1.
Select a band, then select a frequency.
2.
Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
3.
Follow the two steps above for each station
memory preset button you want to set.
NOTE:
If the vehicle’s battery is disconnected,
the clock and station memory preset
buttons (if programmed in auto mode)
will need to be reset.
Using the Controls of Your Cassette Tape
Player (If equipped)
How to insert a tape
Insert a cassette (with the open edge to the
right) firmly into the tape door opening, making
sure the cassette is completely in and “seated.”
NOTE:
A cassette tape can be loaded with the
ignition on whether or not the radio
power is on.
How to locate a desired track on the tape
❑
Using the Automatic Music Search (“AMS”)
Press and hold the “AMS” button (“AMS”
will appear in the display). Then, push the
left (
h
) button to rewind to the beginning
of the current selection or press the right
(
g
) button to fast forward to the beginning
of the next selection.
❑
How to change the side of the tape being
played
The alternate track (other side) of the tape
can be selected at any time by pushing both
fast-wind buttons (
h
and
g
) at the
same time.
52
How to eject the tape
To stop the tape and eject the cassette, press the
“
i
” button. The radio will resume playing.
Using the Dolby
H
B noise reduction feature
Push the
k
button to activate. Push again to
deactivate.
NOTE:
Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. “Dolby” and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
How to view the clock mode
Press the “CLOCK” button to alternate the
frequency and time in the display. In the clock
mode, pressing any radio function will
automatically display the radio frequency for
approximately ten seconds before changing back
to the clock mode.
How to set the clock
1.
Turn the radio on.
2.
Press and hold in the “CLOCK” button.
Press the “SEEK” button left (
b
) to advance
the hours and right (
a
) to advance the
minutes.
NOTE:
The clock displays 12-hour time with
no AM/PM indications.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст