Chery Tiggo 5 (T21). Manual — part 223
18–
81
18
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the wire harness connector E-030.
c. Check if the terminals 3 and 32 of wire harness connector
E-030 is short to power.
a. Using X-431 3G diagnostic tester, select Read Code.
b. Check if DTC P0900, P0902 or P0903 still exists.
4
Check if transmission wire harness connector E-030 is short to power
RT21181150
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
-
+
V
Repair or replace failed circuit
NG
5
Check for DTC
OK
Replace solenoid and wire harness
assembly
NG
System is normal
OK
18–
82
18
DTC
P0928
Gear Shift Lock Solenoid Control Circuit Open
DTC
P0930
Gear Shift Lock Solenoid Control Circuit Low
DTC
P0931
Gear Shift Lock Solenoid Control Circuit High
18–
83
18
ET21180160
TCU
R
7
6
R
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
15
30
YR
YR
21
COMMAND
GEAR SHIFT
1
2
3
4
5
6
7
8
9 10 11
12 13 14 15 16 17 18 19 20 21 22
B-004
B-054
E-029
B-054
E-029
E-030
B
E-030
1
8
9
10
11
2
3
4
5
6
7
W
B-004
W
B-054
BATTERY
TCU
RELAY
ERLY12
A2
J2
F16
85
30
86
87
31
56
3
RL
R
RL
R
EF19
10A
EF46
20A
A1
A2
A3
A4
A5
A6
A7
A8 A9 A10
J2
J1
F12
F24
F11
F23
F10
F22
F9
F21
F8
F20
F7
F19
F6
F18
F5
F17
F4
F16
F3
F15
F2
F14
F1
F13
ENGINE
COMPARTMENT
FUSE AND
RELAY BOX
Gr
E-076
W
E-069
B
E-066
E-069
E-076
E-066
F15
18–
84
18
DTC Confirmation Procedure:
Confirm that battery voltage is between 11 and 14 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC), and make it
communicate with vehicle electronic module by the data network.
Turn ignition switch to ON.
Using X-431 3G diagnostic tester to record and clear the DTCs stored in the TCU.
Turn ignition switch to LOCK and wait for a few seconds.
Turn ignition switch to ON, and then select "Read Code".
If DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent. Please refer to Intermittent
DTC Troubleshooting.
Diagnosis Procedure
HINT:
After the fault is eliminated, verify DTC and symptom again.
a. Turn ignition switch to LOCK.
b. Disconnect the gear selector connector.
c. Check if the gear selector connector is dirty, oxidized, loose or damaged.
DTC Code
DTC Definition
DTC Detection
Condition
DTC Set
Condition
Possible Cause
P0928
Gear Shift Lock
Solenoid Control
Circuit Open
Start engine, apply
brake and then shift
from P gear to R gear
The solenoid
output feedback
voltage is
normal, gear
shifting solenoid
feedback current
is less than the
standard value
Solenoid circuit
open circuit or
short circuit
Gear shifting lock
solenoid failure
P0930
Gear Shift Lock
Solenoid Control
Circuit Low
When the
solenoid output
feedback voltage
is normal, gear
shifting lock
solenoid
feedback current
is higher than the
standard value
P0931
Gear Shift Lock
Solenoid Control
Circuit High
The solenoid
output feedback
voltage is
normal, gear
shifting solenoid
feedback current
is less than the
standard value
1
Check wire harness connector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст