Chery Tiggo 5 (T21). Manual — part 222
18–
77
18
DTC
P0900
Clutch Actuator Circuit Open
DTC
P0902
Clutch Actuator Circuit Low
DTC
P0903
Clutch Actuator Circuit High
18–
78
18
ET21180150
BATTERY
TCU
TCU
RELAY
ERLY12
A2
J2
F16
85
30
86
87
31
56
3
32
RL
R
WR
RL
R
4
CLUTCH CONTROL
SOLENOID
R
9
EF19
10A
EF46
20A
A1
A2
A3
A4
A5
A6
A7
A8 A9 A10
J2
J1
F12
F24
F11
F23
F10
F22
F9
F21
F8
F20
F7
F19
F6
F18
F5
F17
F4
F16
F3
F15
F2
F14
F1
F13
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
ENGINE
COMPARTMENT
FUSE AND
RELAY BOX
CONNECTOR B
Gr
E-076
W
E-069
B
E-066
B
E-030
E-069
E-076
E-052
E-030
E-066
F15
6
5
4
3
2
1
7
8
9
10
Gr
E-052
18–
79
18
DTC Confirmation Procedure:
Confirm that battery voltage is between 11 and 14 V before performing the following procedures.
Turn ignition switch to LOCK.
Connect X-431 3G diagnostic tester (the latest software) to Data Link Connector (DLC), and make it
communicate with vehicle electronic module by the data network.
Turn ignition switch to ON.
Using X-431 3G diagnostic tester to record and clear the DTCs stored in the TCU.
Turn ignition switch to LOCK and wait for a few seconds.
Turn ignition switch to ON, and then select "Read Code".
If DTC is detected, the malfunction indicated by the DTC is current. Go to the diagnosis procedure - Step 1.
If DTC is not detected, the malfunction indicated by the DTC is intermittent. Please refer to Intermittent
DTC Troubleshooting.
Diagnosis Procedure
HINT:
After the fault is eliminated, verify DTC and symptom again.
a. Turn ignition switch to LOCK.
b. Disconnect the transmission wire harness connector.
c. Check if the transmission wire harness connector is dirty, oxidized, loose or damaged.
DTC Code
DTC Definition
DTC Detection
Condition
DTC Set
Condition
Possible Cause
P0900
Clutch Actuator Circuit
Open
Start engine and
engage D or R gear for
at least 5 seconds
The solenoid
output feedback
voltage is
normal, clutch
solenoid
feedback current
is less than the
standard value
Solenoid circuit
open circuit or
short circuit
Clutch control
solenoid failure
P0902
Clutch Actuator Circuit
Low
When the
solenoid output
feedback voltage
is normal, clutch
solenoid
feedback current
is higher than the
standard value
P0903
Clutch Actuator Circuit
High
When the
solenoid output
feedback voltage
is normal, clutch
solenoid
feedback current
is less than the
standard value
1
Check wire harness connector
18–
80
18
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the connectors E-052 and E-030.
c. Check for continuity between the terminal 4 and 9 of
connector E-052 and terminal 32 and 3 of connector E-030.
a. Turn ignition switch to LOCK and disconnect the negative
battery cable.
b. Disconnect the wire harness connector E-030.
c. Check for continuity between the terminals 3 and 32 of
wire harness connector E-030 and ground.
Repair fault
NG
2
Check engine compartment wire harness
OK
-
+
RT21181130
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
E-052
6
5
4
3
2
1
7
8
9
10
Repair or replace failed circuit
NG
3
Check for continuity between wire harness connector E-030 and ground
OK
-
+
RT21181140
E-030
29 30 31 32 33 34 35 36 37 38 39 40 41 42
1 2 3 4 5 6 7 8 9 10 11 12 13 14
43 44 45 46 47 48 49 50 51 52 53 54 55 56
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Repair or replace failed circuit
NG
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст