Chery Tiggo 5 (T21). Manual — part 117
07–
54
07
If camshaft axial clearance is not within the specified
range, replace camshaft.
Installation
1. Clean the intake camshaft, exhaust camshaft, and camshaft bearing caps.
2. Apply seal gum to the bottom of camshaft 1st bearing cap
evenly as shown in the illustration.
3. First screw the camshaft bearing cap fixing bolts by hand without tightening.
4. Tighten the camshaft bearing cap fixing bolts in the order
shown in the illustration.
5. Install the camshaft oil seals (
6. Other installation procedures are in the reverse order of removal.
Measurement Item
Specification
(mm)
Intake Camshaft Axial Clearance
0.15 - 0.20
Exhaust Camshaft Axial Clearance
0.15 - 0.20
RT21070490
CAUTION
Pay attention not to apply seal gum into the oil hole.
E1
I1
I2
I3
I4
E2
E3
E4
RT21070500
7
9
10
8
3
4
1
2
5
6
5
6
1
2
3
4
7
8
11
12
07–
55
07
Cylinder Head
Description
1 - Valve Cotter
2 - Valve Spring Upper Seat
3 - Valve Spring
4 - Valve Oil Seal
5 - Valve Spring Lower Seat
6 - Valve Guide
7 - Cylinder Head Fixing Bolt
8 - Cylinder Head Fixing Bolt Washer
9 - Cylinder Head
10 - Stud
11 - Cylinder Gasket
12 - Exhaust Valve
13 - Intake Valve
RT21070510
×10
×10
×10
×8
10
11
12
9
7
1
2
3
4
5
6
8
13
07–
56
07
Removal
1. Release fuel system pressure (
).
2. Turn off all the electrical equipment and ignition switch.
3. Disconnect the negative battery cable.
4. Drain the coolant (
).
5. Remove the high-voltage cables (
6. Remove the spark plugs (
).
7. Remove the ignition coil (
8. Remove the thermostat (
).
9. Remove the thermostat seat (
10.Remove the fuel rail injector assembly (
).
11.Remove the exhaust manifold assembly (
).
12.Disconnect the intake VVT control vavle connector
(arrow).
13.Disconnect the exhaust VVT control vavle connector
(arrow).
14.Remove the electronic throttle assembly (
15.Remove the intake manifold assembly (
16.Remove the accessory drive belt (
).
17.Use an engine equalizer to hang the engine.
18.Remove the engine timing belt (
).
19.Remove the cylinder head cover (
20.Remove the exhaust camshaft phaser assembly (
21.Remove the intake camshaft phaser assembly (
22.Remove the timing belt rear cover (
RT21070520
RT21070530
07–
57
07
23.Rotate intake/exhaust camshafts to a proper position with
an appropriate wrench, and remove the cylinder head
fixing bolts in the sequence from (1) to (10) shown in the
illustration.
24.Remove the cylinder head and cylinder head gasket.
Disassembly
1. Remove the camshaft (
).
2. Remove the rocker arm and hydraulic lifter (
).
3. Using a special tool (valve spring compressor) (1),
compress the valve spring and remove the valve cotter
(2) with a flexional magnetic rod.
RT21070540
3
7
6
2
4
8
9
5
1
10
CAUTION
Failure to follow the sequence to remove cylinder head bolts will cause cylinder head deformation.
CAUTION
Replace the used gasket with a new one.
RT21070550
2
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст