Chery Tiggo 5 (T21). Manual — part 525
49–
11
49
Front Doorsill Pressure Plate Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the front left doorsill pressure plate assembly.
a. Using an interior crow plate, pry up the claws of front
doorsill pressure plate assembly, and remove the front
left doorsill pressure plate assembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the front door scuff plate
assembly.
Appropriate force should be applied when removing the front door scuff plate assembly. Be careful not to
operate roughly.
Prevent interior and body paint from being scratched when removing the front door scuff plate assembly.
RT21490050
CAUTION
Make sure front doorsill pressure plate assembly is installed in place during installation.
Make sure to check the fitting gap between front doorsill pressure plate assembly and B-pillar lower
protector assembly, A-pillar lower protector assembly for uniformity after installing front doorsill pressure
plate assembly.
49–
12
49
Rear Doorsill Pressure Plate Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove rear left doorsill pressure plate assembly.
a. Using an interior crow plate, pry up the claws of rear
doorsill pressure plate assembly, and remove the rear
left doorsill pressure plate assembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the rear doorsill pressure plate
assembly.
Appropriate force should be applied when removing the rear doorsill pressure plate assembly. Be careful
not to operate roughly.
Prevent interior and body paint from being scratched when removing the rear doorsill pressure plate
assembly.
RT21490060
CAUTION
Make sure rear doorsill pressure plate assembly is installed in place during installation.
Make sure to check the fitting gap between rear doorsill pressure plate assembly and B-pillar lower
protector assembly, C-pillar lower protector assembly for uniformity after installing the rear doorsill
pressure plate assembly.
49–
13
49
Back Doorsill Pressure Plate Assembly
Removal
1. Remove the back door weatherstrip (
2. Remove the luggage compartment carpet assembly (
3. Remove the back doorsill pressure plate assembly.
a. Remove 2 plastic clips (arrow) from the back doorsill
pressure plate assembly.
b. Using an interior crow plate, pry off the clips from the
back doorsill pressure plate assembly and remove the
back doorsill pressure plate assembly.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the back doorsill pressure
plate assembly.
Appropriate force should be applied when removing the back doorsill pressure plate assembly. Be
careful not to operate roughly.
Prevent interior and body paint from being scratched when removing the back doorsill pressure plate
assembly.
RT21490070
RT21490080
CAUTION
Make sure damaged clips are replaced and back doorsill pressure plate assembly is installed in place
when installing back doorsill pressure plate assembly.
49–
14
49
Front Door Opening Weatherstrip
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the front left doorsill pressure plate assembly (
2. Remove the front left door opening weatherstrip.
a. Remove the front left door opening weatherstrip by
gently pulling it along edges from one corner of the
front door opening weatherstrip.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the front door opening
weatherstrip.
Appropriate force should be applied when removing the front door opening weatherstrip, and avoid
operating roughly.
DO NOT damage the front door opening weatherstrip when removing it.
RT21490180
CAUTION
The front door opening weatherstrip and body should be properly fitted with a certain degree of gripping
force and the weatherstrip should not fall off easily when installing the front door opening weatherstrip.
When installing the front door opening weatherstrip, tap all around uniformly with a rubber hammer to
install it in place. The surface of weatherstrip should have no defects, such as tapped dents, deformation
and warpage after installation.
After installing the front door opening weatherstrip, do not remove or install it unless it is necessary.
Otherwise the weatherstrip holding force of installation may be reduced.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст