Chery Tiggo 5 (T21). Manual — part 526
49–
15
49
Rear Door Opening Weatherstrip
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the rear left doorsill pressure plate assembly (
2. Remove the rear left door opening weatherstrip.
a. Remove the rear left door opening weatherstrip by
gently pulling it along edges from one corner of the
rear door opening weatherstrip.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the rear door opening
weatherstrip.
Appropriate force should be applied when removing the rear door opening weatherstrip, and avoid
operating roughly.
DO NOT damage the rear door opening weatherstrip when removing it.
RT21490190
CAUTION
The rear door opening weatherstrip and body should be properly fitted with a certain degree of gripping
force and the weatherstrip should not fall off easily when installing the rear door opening weatherstrip.
When installing the rear door opening weatherstrip, tap all around uniformly with a rubber hammer to
install it in place. The surface of weatherstrip should have no defects, such as tapped dents, deformation
and warpage after installation.
After installing the rear door opening weatherstrip, do not remove or install it unless it is necessary; or the
weatherstrip holding force of installation may be reduced.
49–
16
49
Back Door Weatherstrip
Removal
1. Remove the back door weatherstrip.
a. Remove the back door weatherstrip by gently pulling it
along edges from one corner of the back door
weatherstrip.
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the back door weatherstrip.
Appropriate force should be applied when removing the back door weatherstrip, and avoid operating
roughly.
DO NOT damage the back door weatherstrip when removing it.
RT21490200
CAUTION
The back door weatherstrip and body should be properly fitted with a certain degree of gripping force and
the weatherstrip should not fall off easily when installing the back door weatherstrip.
When installing the back door weatherstrip, tap all around uniformly with a rubber hammer to install it in
place. The surface of weatherstrip should have no defects, such as tapped dents, deformation and
warpage after installation.
After installing the back door weatherstrip, do not remove or install it unless it is necessary; or the
weatherstrip holding force of installation may be reduced.
49–
17
49
A-pillar Upper Protector Assembly
Removal
HINT:
Use the same procedures for the right side and left side.
Procedures listed below are for the left side.
1. Remove the front left door opening weatherstrip (
).
2. Remove the left A-pillar upper protector assembly.
a. Using an interior crow plate, pry off the clips from the
A-pillar upper protector assembly.
b. Disconnect the high pitched speaker connector
(arrow), and remove the left A-pillar protector
assembly.
c. Remove 3 fixing screws (arrow) from the high pitched
speaker assembly.
(Tightening torque: 3 ± 0.5 N·m)
d. Remove the high pitched speaker assembly from the
A-pillar protector assembly.
CAUTION
Make sure to wear safety equipment to prevent accidents when removing the A-pillar upper protector
assembly.
Appropriate force should be applied when removing the A-pillar upper protector assembly. Be careful not
to operate roughly.
Prevent interior and body paint from being scratched when removing the A-pillar upper protector
assembly.
RT21490100
1
2
3
4
5
RT21490101
RT21490102
49–
18
49
Installation
Installation is in the reverse order of removal.
CAUTION
Make sure damaged clips are replaced and A-pillar upper protector assembly is installed in place when
installing A-pillar upper protector assembly.
A-pillar upper protector assembly and front door opening weatherstrip should be fitted closely after
installing A-pillar upper protector assembly.
A-pillar upper protector assembly and instrument panel and roof headlining should be fitted closely after
installing A-pillar upper protector assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст