Chery Tiggo 5 (T21). Manual — part 156
12–
25
12
Fan Controller
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the engine trim cover assembly (
).
4. Remove the fan controller.
a. Disconnect the fan controller connectors (arrow).
b. Remove 2 fixing bolts (arrow) from fan controller.
(Tightening torque: 7 ± 1.5 N·m)
c. Remove the fan controller from cooling fan assembly.
Installation
Installation is in the reverse order of removal.
WARNING
Perform removal procedures with engine compartment at low temperature after cooling fan stops
completely, otherwise rotating cooling fan or hot components of engine compartment may cause serious
injury.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21120210
RT21120220
12–
26
12
Cooling Fan Assembly
On-vehicle Inspection
1. Apply battery voltage to the specified connector terminals
of cooling fan respectively according to the table below,
and check that the cooling fan operates smoothly when
applying battery voltage.
If result is not as specified, replace cooling fan assembly (
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the engine trim cover assembly (
).
4. Remove the air induction pipe assembly (
5. Remove the radiator grille assembly (
6. Remove the water tank upper crossmember trim board (
7. Remove the engine hood lock assembly (
8. Remove the tank upper crossmember assembly (
9. Remove the cooling fan assembly.
-
+
1
2
3
RT21120221
Multimeter
Condition
Condition
Specified
Condition
Battery positive
(+) - Terminal 1
Always
Operates
smoothly
Battery negative
(-) - Terminal 3
WARNING
Perform removal procedures with engine compartment at low temperature after cooling fan stops
completely, otherwise rotating cooling fan or hot components of engine compartment may cause serious
injury.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
12–
27
12
a. Disconnect the fan controller connector (arrow).
b. Remove the wire harness clips (arrow) from engine compartment contact switch, and move away the
engine compartment contact switch from cooling fan assembly.
c. Remove the fixing band (1) of engine outlet hose from
cooling fan assembly.
d. Remove 4 fixing bolts (arrow) from cooling fan
assembly.
(Tightening torque: 7 ± 1 N·m)
e. Remove the cooling fan assembly from radiator assembly.
10.Remove the fan controller.
a. Disconnect the fan controller connector (1).
b. Remove 2 fixing bolts (arrow) from the fan controller,
and remove the fan controller from the cooling fan
assembly.
(Tightening torque: 7 ± 1.5 N·m)
RT21120230
1
RT21120240
RT21120250
1
RT21120260
12–
29
12
Radiator Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the engine trim cover assembly (
).
4. Remove the radiator grille assembly (
5. Remove the water tank upper crossmember trim board (
6. Remove the engine hood lock assembly (
7. Move away the hood lock cable from tank upper crossmember assembly.
8. Remove the tank upper crossmember assembly (
9. Drain the coolant (
).
10.Remove the cooling fan assembly (
11.Remove the radiator assembly.
a. Loosen the elastic clamp (arrow) and disconnect the
connection between engine outlet hose and radiator
assembly.
WARNING
Always make sure engine is cold before operating cooling system.
Never open expansion tank cap or remove drain cock plug when engine is operating or cooling system
overheats. The engine coolant and steam with high-pressure and overheat may flow out and cause
serious personal injury.
If your body contacts coolant accidentally, clean it with water immediately. If it is serious, please go to
hospital.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21120270
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст