Chery Tiggo 5 (T21). Manual — part 428
37–
52
37
Inspection
1. Check back door lock assembly.
a. Using ohm band of digital multimeter, check for
continuity between terminals of back door lock
assembly according to the table below.
If result is not as specified, replace back door lock
assembly.
2. Check back door lock assembly.
a. Apply battery voltage to the terminals of back door
lock assembly connector and check the operation of
back door lock assembly according to the table below.
Rear Right Door Lock Assembly
If result is not as specified, replace back door lock
assembly.
Installation
Installation is in the reverse order of removal.
RT21370241
1 2 3 4 5 6
-
+
Measurement Condition
Switch
Condition
Specified
Condition
Terminal 1 - Terminal 2
ON
Continuity
OFF
Continuity
Terminal 3 - Terminal 4
ON
Continuity
OFF
No
continuity
RT21370242
-
+
1 2 3 4 5 6
Measurement Condition
Specified
Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
ON
CAUTION
Check if connector is installed correctly when installing back door lock assembly.
Install the cable in place when installing back door lock assembly.
Check if back door lock operates properly after installing back door lock assembly.
37–
53
37
Back Door Lock Striker Assembly
Removal
1. Remove the back doorsill pressure plate assembly (
2. Remove the back door lock striker assembly.
a. Remove 2 fixing crews (arrow) from back door lock
striker assembly.
(Tightening torque: 10 ± 1 N·m)
b. Remove the back lock latch.
Installation
Installation is in the reverse order of removal.
CAUTION
Be sure to the wear safety equipment to prevent accidents when removing back door lock striker
assembly.
Try to prevent body paint surface from being scratched when removing back door lock striker assembly.
RT21370250
CAUTION
Try to prevent body paint surface from being scratched when installing back door lock striker assembly.
37–
54
37
Low Frequency Antenna
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the auxiliary fascia console rear cover plate assembly.
a. Remove the fixing screw from auxiliary fascia console
rear cover plate assembly.
(Tightening torque: 1.5 ± 0.5 N·m)
b. Open the armrest box assembly.
c. Using a screwdriver wrapped with protective tape, pry
up the claws on auxiliary fascia console rear cover
plate assembly, and remove the auxiliary fascia
console rear cover plate assembly.
4. Remove the low/medium frequency antenna.
a. Disconnect the connector (arrow) from low/medium
frequency antenna.
b. Using a screwdriver wrapped with protective tape, pry
up the clip on low/medium frequency antenna, and
remove the low/medium frequency antenna.
CAUTION
Be sure to the wear safety equipment to prevent accidents when removing low frequency antenna.
Try to prevent body paint surface from being scratched when low frequency antenna.
RT21370480
RT21370481
RT21370490
37–
55
37
5. Remove the anti-theft coil.
a. Remove the auxiliary fascia console assembly (
).
HINT:
Anti-theft coil connector has been disconnected when
removing the auxiliary fascia console assembly.
b. Detach the claws (arrow), and remove the anti-theft
coil.
6. Remove the front low frequency antenna.
a. Disconnect the connector (arrow) from front low
frequency antenna.
b. Using a screwdriver wrapped with protective tape, pry
up the clip on front low frequency antenna, and
remove the front low frequency antenna.
7. Remove the rear low frequency antenna.
a. Remove the rear left seat assembly (
b. Disconnect the connector (arrow) from rear low
frequency antenna.
c. Using a screwdriver wrapped with protective tape, pry
up the clip on rear low frequency antenna, and
remove the rear low frequency antenna.
8. Remove the rear bumper assembly (
9. Remove the back door opener low frequency antenna.
RT21450181
RT21450191
RT21370470
RT21370510
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст