Chery Tiggo 5 (T21). Manual — part 410
36–
23
36
Inspection
1. Check wiper switch assembly.
a. Using a digital multimeter, check for continuity
between terminals of wiper switch assembly
according to the table below.
If result is not as specified, replace wiper switch
assembly.
Installation
Installation is in the reverse order of removal.
REAR
-
+
1
2
3
4
5
6
7
8
9 10
RT21360040
Multimeter
Connection
Switch
Condition
Specified
Condition
Terminal 1 -
Terminal 3
MIST
Continuity
Terminal 2 -
Terminal 3
INT
Continuity
Terminal 1 -
Terminal 3
LO
Continuity
Terminal 1, 2 -
Terminal 3
HI
Continuity
Terminal 3 -
Terminal 4
FRONT WASHER
Continuity
Terminal 3, 7 -
Terminal 9
REAR WASHER
Continuity
CAUTION
Always operate carefully to prevent components from being damaged when installing wiper switch
assembly.
Install connector in place when installing wiper switch assembly.
Check wiper switch for proper operation after installing wiper switch assembly.
36–
24
36
Front Wiper Arm Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the front wiper arm blade.
a. Lift up the front wiper arm assembly in the direction of
arrow as shown in the illustration.
b. Pull the front wiper arm blade out of front wiper arm
assembly in the direction of arrow as shown in the
illustration.
4. Remove the front wiper arm assembly.
a. Using a screwdriver wrapped with protective tape,
remove the front wiper arm trim caps (1).
b. Remove 2 fixing nuts (arrow) from front wiper arm
assembly and remove the front wiper arm assembly.
(Tightening torque: 18 ± 2 N·m)
CAUTION
Be sure to wear safety equipment to prevent accidents when removing front wiper arm assembly.
Appropriate force should be applied when removing front wiper arm assembly. Be careful not to operate
roughly.
Try to prevent front windshield assembly from being scratched when removing front wiper arm assembly.
RT21360050
RT21360060
RT21360070
1
36–
25
36
Installation
Installation is in the reverse order of removal.
HINT:
Always adjust the front wiper arm assembly to the proper
position during installation.
Pay attention to the locating point on front windshield
assembly during assembly. Wiper arm blade should be
pressed against the locating point as shown in the
illustration.
CAUTION
Always operate carefully to prevent other components from being damaged when installing front wiper
arm assembly.
Make sure to tighten fixing nuts to the specified torque when installing front wiper arm assembly.
Check front wiper arm assembly for proper operation after installation.
RT21360080
36–
26
36
Front Wiper Motor Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the front wiper arm assembly (
).
4. Remove the front windshield lower garnish assembly (
5. Remove the wiper motor and link rod assembly.
a. Disconnect the connector (1) from wiper motor and
link rod assembly.
b. Remove 3 fixing bolts (arrow) from wiper motor and
link rod assembly.
(Tightening torque: 10 ± 1 N·m)
c. Remove the wiper motor and link rod assembly.
6. Remove the front wiper motor assembly.
a. Remove 3 fixing bolts (arrow) from front wiper motor
assembly.
(Tightening torque: 10 ± 1 N·m)
b. Remove the fixing nut (1) from front wiper motor
assembly.
(Tightening torque: 10 ± 1 N·m)
c. Using a screwdriver wrapped with protective tape,
separate the front wiper motor assembly and wiper
link rod.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing front wiper motor assembly.
Appropriate force should be applied when removing front wiper motor assembly. Be careful not to
operate roughly.
Try to prevent body paint surface from being scratched when removing front wiper motor assembly.
1
RT21360090
1
RT21360100
RT21360101
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст