Chery Tiggo 5 (T21). Manual — part 409
36–
19
36
g. Disconnect the engine compartment wire harness
connectors E-069 and E-039.
h. Using a digital multimeter, check for continuity between
engine compartment wire harness connectors E-069 and
E-039 according to the value(s) in the table below.
i. Disconnect the engine compartment wire harness
connector E-077 and ground E-078.
j. Using a digital multimeter, check for continuity between
engine compartment wire harness connector E-077 and
ground E-078 according to the value(s) in the table
below.
k. Disconnect the engine compartment wire harness
connector E-040 and ground E-032.
l. Using a digital multimeter, check for continuity between
engine compartment wire harness connector E-040 and
ground E-032 according to the value(s) in the table
below.
-
+
RT21360480
E-069
F12
F24
F11
F23
F10
F22
F9
F21
F8
F20
F7
F19
F6
F18
F5
F17
F4
F16
F3
F15
F2
F14
F1
F13
E-039
1
2
Multimeter
Connection
Condition
Specified
Condition
E-069 (F8) -
E-039 (1)
Always
Continuity
-
+
RT21360490
E-077
4
3
2
1
E-078
Multimeter
Connection
Condition
Specified
Condition
E-077 (4) - E-078
Always
Continuity
-
+
RT21360500
E-032
E-040
1
2
Multimeter
Connection
Condition
Specified
Condition
E-040 (2) - E-032
Always
Continuity
36–
20
36
m. Disconnect the engine compartment wire harness
connector E-039 and ground E-032.
n. Using a digital multimeter, check for continuity between
engine compartment wire harness connector E-039 and
ground E-032 according to the value(s) in the table
below.
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Disconnect the back door wire harness connectors T-004
and T-007.
d. Using a digital multimeter, check for continuity between
back door wire harness connectors T-004 and T-007
according to the value(s) in the table below.
-
+
RT21360510
E-032
E-039
1
2
Multimeter
Connection
Condition
Specified
Condition
E-039 (2) - E-032
Always
Continuity
Repair or replace engine compartment
wire harness and connector
NG
9
Check back door wire harness and connector
OK
-
+
RT21360520
1
9
10
11
12
13
14
15
2
3
4
5
6
7
8
T-004
1 2 3
T-007
Multimeter
Connection
Condition
Specified
Condition
T-004 (1) - T-007
(2)
Always
Continuity
T-004 (12) - T-007
(3)
Always
Continuity
T-004 (11) - T-007
(1)
Always
Continuity
Repair or replace back door wire harness
and connector
NG
OK
36–
21
36
a. Connect all connectors.
b. Connect the negative battery cable.
c. Turn ignition switch ON.
d. Use the X-431 3G diagnostic tester (the latest software) to record and clear the DTCs stored in Body
Control Module (BCM).
e. Turn ignition switch to LOCK and wait for a few seconds.
f. Turn ignition switch ON.
g. Use the X-431 3G diagnostic tester (the latest software) to read DTCs stored in Body Control Module
(BCM) again.
h. Read DTCs.
10
Reconfirm DTCs
Result
Precede to
DTCs B101471, B101571, B101671, B101713,
B101771, B101813, B101871 are output
NG
No DTCs are output
OK
Replace Body Control Module (BCM)
NG
System operates normally
OK
36–
22
36
ON-VEHICLE SERVICE
Wiper Switch Assembly
Removal
1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the instrument cluster (
).
4. Remove the wiper switch assembly.
a. Disconnect the wiper switch assembly connector
(arrow).
b. Using a screwdriver wrapped with protective tape,
press the claws of wiper switch assembly and remove
the wiper switch assembly by gently sliding outward.
CAUTION
Be sure to wear safety equipment to prevent accidents when removing wiper switch assembly.
Appropriate force should be applied when removing wiper switch assembly. Be careful not to operate
roughly.
Try to prevent interior and body paint surface from being scratched when removing wiper switch
assembly.
RT21360020
RT21360030
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст