Chery Tiggo 5 (T21). Manual — part 301
27–
8
27
ON-VEHICLE SERVICE
Adjustment
Abnormal parking brake operation may be caused by the worn brake shoe lining, incorrect brake shoe
clearance adjustment, incorrect parking brake control mechanism stroke or incorrect parking brake
component installation. Perform the following procedures to adjust the parking brake control mechanism
stroke:
1. Support and raise the vehicle to a proper height.
2. Remove the rear wheel (
3. Remove the rear brake disc (
4. Remove the auxiliary fascia console assembly (
).
5. Adjust the parking brake shoe clearance:
a. Fully release the parking brake control mechanism.
b. Using a flat tip screwdriver, pry off the brake shoe
adjusting hole plug, rotate the brake shoe clearance
adjustment mechanism assembly to adjust parking
brake shoe clearance, and attempt to rotate the rear
brake disc by hand to confirm that brake disc rotates
freely.
c. Check that there is no brake stuck for the brake shoe.
6. Adjust the parking brake control mechanism stroke:
a. Fully release the parking brake control mechanism.
b. Rotate the parking brake control mechanism
adjustment nut, until the parking brake control
mechanism stroke is correct.
c. Correct judging method: after adjustment, fully release parking brake control mechanism and rotate
rear wheel by hand.
OK: Rear wheel can be rotated freely without dragging.
Pull up parking brake control mechanism until 1 clicking sound is heard. There is resistance when
rotating rear wheel by hand. Pull up parking brake control mechanism until 5 to 6 clicking sounds are
heard and the rear wheel cannot rotate.
d. When operating the parking brake control mechanism, check that brake warning light illuminates at the
first click.
OK: Parking brake warning light always illuminates at the first click.
e. If result is not as specified, repeat above procedures until the parking brake control mechanism stroke
is proper.
7. Install the auxiliary fascia console assembly (
).
8. Install the rear brake disc (
).
9. Install the rear wheel (
(Tightening torque: 110 ± 10 N·m)
RT21270020
Shrink
Expansion
RT21270030
27–
9
27
Parking Brake Switch Assembly
On-vehicle Inspection
1. Disconnect parking brake switch assembly connector,
and check the continuity of parking brake switch
assembly with ohm band of digital multimeter as shown
in the table below.
Standard Condition
If result is not as specified, replace parking brake switch
assembly.
Removal
1. Fix the tire and wheel assembly.
2. Remove the auxiliary fascia console assembly (
).
3. Remove the parking brake switch assembly.
a. Disconnect the parking brake switch assembly wire
harness connector (arrow) as shown in the illustration.
RT21270040
1
-
+
Multimeter
Connection
Condition
Specified
Condition
Terminal 1 - Body
ground
Parking brake
applied (switch
pin released)
Continuity
Parking brake
released (switch
pin pushed)
No continuity
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21270050
27–
10
27
b. Using a cross screwdriver, loosen the fixing screw
(arrow) of parking brake switch assembly.
c. Remove the parking brake switch assembly.
Inspection
1. Check parking brake switch assembly.
a. Check parking brake switch assembly for wear or break. Replace parking brake switch assembly as
necessary.
b. Check if parking brake switch assembly compressed spring is damaged or weak elasticity. Replace
parking brake switch assembly as necessary.
Installation
Installation is in the reverse order of removal.
RT21270060
27–
11
27
Parking Brake Control Mechanism Assembly
Removal
1. Fix the tire and wheel assembly.
2. Remove the auxiliary fascia console assembly (
).
3. Remove the parking brake switch assembly (
).
4. Remove the parking brake control mechanism assembly.
a. Fully release the parking brake control mechanism.
b. Loosen the locking nut (arrow) of parking brake
control mechanism assembly to release the tension of
parking brake cable assembly as shown in the
illustration.
c. Remove 4 coupling bolts (arrow) between parking
brake control mechanism assembly and body.
(Tightening torque: 23 ± 2 N·m)
d. Disengage the parking brake rear cable assembly
from two grooves (arrow) on the rear of parking brake
control mechanism assembly.
e. Remove the parking brake control mechanism assembly.
CAUTION
Be sure to wear necessary safety equipment to prevent accidents when repairing.
Try to prevent body paint surface from being scratched during removal and installation.
RT21270030
RT21270070
RT21270080
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст