Chery Tiggo 5 (T21). Manual — part 307
28–
10
28
ON-VEHICLE SERVICE
Steering Wheel Assembly
Removal
1. Set steering wheel to straight-ahead position.
2. Turn off all the electrical equipment and ignition switch.
3. Disconnect the negative battery cable.
4. Remove the driver airbag assembly (
5. Remove the steering wheel assembly.
a. Secure the steering wheel assembly, and put
matchmarks on the steering wheel assembly and
steering column assembly, then remove the steering
wheel assembly fixing nut.
(Tightening torque: 35 ± 3 N·m)
b. As shown in the illustration, install the steering wheel
remover, and then tighten it with a wrench to loosen
the steering wheel assembly from the steering column
assembly.
WARNING
Be sure to read the precautions for SRS airbag before removing the steering wheel (
CAUTION
Wait at least 90 seconds after disconnecting the negative battery cable to prevent airbag and belt
pretensioner from being activated.
3
4
5
6
7
8
1
2
x1000
H
20
40
60
80
100 120
140
160
180
200
220
L
R
MODE
VOL-
VOL+
NAV1
MENU
BAND
SET
2 4 R
3 5
1
A/C
RES/+
SET/-
ON
OFF
RT21280040
OFF
5
6
7
8
MODE
VOL-
VOL+
RT21280050
28–
11
28
c. Cut the wire harness band (arrow).
d. Disconnect the steering wheel quick button connector
(arrow).
e. Remove the steering wheel assembly.
Inspection
1. Check the steering wheel assembly body for damage or deformation. Replace the steering wheel
assembly if necessary.
2. Check the spline in the steering wheel assembly for damage. Replace the steering wheel assembly if
necessary.
3
4
5
6
7
8
1
2
x1000
H
20
40
60
80
100 120
140
160
180
200
220
L
R
MODE
VOL-
VOL+
NAV1
MENU
BAND
SET
2 4 R
3 5
1
A/C
RES/+
SET/-
ON
OFF
RT21280041
RT21280060
CAUTION
Be careful when removing the steering wheel assembly to prevent damage to the airbag connector, horn
connector and quick button connector on the spiral cable.
28–
12
28
Installation
1. Adjust the spiral cable to correct position.
HINT:
Fully turn the spiral cable inner circle clockwise when
realigning the center, and then turn it counterclockwise to
align with ►◄ while yellow ball (arrow) occurs in the
clear vertical window. Failure to follow these instructions
may affect normal function of airbag system and cause
injury to driver.
2. Pass the airbag connector, horn connector through the hole of steering wheel assembly, and connect the
steering wheel quick button connector. Then align the matchmarks on steering wheel assembly and
steering column assembly to install the steering wheel assembly.
3. Other installation procedures are in the reverse order of removal.
CAUTION
Check that front wheels are in the straight-ahead position before installing steering wheel assembly.
ON
OFF
REAR
INT
PULL
MIST
OFF
INT
LO
HI
OFF
PBT
RT21280070
CAUTION
Tighten steering wheel assembly fixing nut to the specified torque.
Install each connector in place.
After repairing, check that airbag system operates normally.
28–
13
28
Combination Switch Cover
Removal
1. Set steering wheel to straight-ahead position.
2. Turn off all the electrical equipment and ignition switch.
3. Remove the combination switch cover.
HINT:
Remove the steering wheel assembly first, and then remove combination switch cover if necessary.
a. Turn the steering wheel to left, and remove the left
side fixing screw (arrow) from the combination switch
cover.
(Tightening torque: 2 ± 0.5 N·m)
b. Turn the steering wheel to right, and remove the right
side fixing screw (arrow) from the combination switch
cover.
(Tightening torque: 2 ± 0.5 N·m)
c. Remove the lower fixing screw (arrow) from the
combination switch cover.
(Tightening torque: 2 ± 0.5 N·m)
RT21280080
MODE
VOL+
<
<
VOL-
ON
OFF
RESI+
SETI-
60
40
20
220
MIST
OFF
INT
INT
LO
HI
PULL
0
BAND
NAVI
MENU
A/C
OFF ON
SET
<
<
RT21280090
L R
2
3
OFF
OFF
1
RT21280100
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст