Chery Tiggo 5 (T21). Manual — part 308
28–
14
28
d. Disengage the connecting clip between upper cover
and lower cover, and then disengage upper cover and
lower cover to remove the lower cover.
e. Disengage 6 clips between upper cover and steering
column dust gasket, and then remove the upper
cover.
Inspection
1. Check the combination switch upper and lower covers for damage or deformation. Replace the upper and
lower covers if necessary.
2. Check if upper and lower cover clips are normal. Replace the upper and lower covers if necessary.
OFF
RT21280110
80
0
x1000
rpm
ENGINE
START
STOP
2
OFF
OFF
RT21280111
CAUTION
Operate carefully to prevent damage to components during removal.
28–
15
28
Installation
1. Loosen steering wheel adjusting handle, and adjust steering column assembly to the uppermost position,
then tighten the adjusting handle to the uppermost position.
2. Insert steering column lower cover from right side of ignition switch at an angle, and then install the
adjusting handle into the cover hole.
3. After adjusting lower cover, install upper cover and fix upper and lower cover clips in place, then install the
self-tapping screws.
CAUTION
Tighten the self-tapping screws in place.
Operate carefully to prevent damage to components during installation.
28–
16
28
Steering Column with Intermediate Shaft Assembly (without EPS)
Removal
1. Set steering wheel to straight-ahead position.
2. Turn off all the electrical equipment and ignition switch.
3. Disconnect the negative battery cable.
4. Remove the driver airbag (
).
5. Remove the steering wheel assembly (
6. Remove the combination switch cover (
).
7. Remove the spiral cable (
8. Remove the combination switch assembly.
a. Disconnect the light combination switch connector (1)
and wiper and washer combination switch connector
(2).
b. Loosen the combination switch clamp and pull the
combination switch outward, then disconnect the
combination switch from the steering column to
remove the combination switch.
9. Remove the steering column with intermediate shaft assembly.
a. Disconnect the ignition starting switch connector (1),
key switch connector (2) and connector (3) of ignition
switch illumination light and anti-theft coil.
0
E
C
X1000
rpm
0
1
2
3
4
5
6
7
8
H
km/h
20
40
60
80
100 120
140
160
180
200
220
F
L
R
ON
OFF
OFF
OFF
OFF
OFF
REAR
MIST
INT
INT
LO
HI
PULL
2
3
NAVI
1
2
RT21280120
0
E
C
X1000
rpm
0
1
2
3
4
5
6
7
8
H
km/h
20
40
60
80
100 120
140
160
180
200
220
F
L
R
ON
OFF
OFF
OFF
OFF
OFF
REAR
MIST
INT
INT
LO
HI
PULL
2
3
NAVI
RT21280130
2
3
1
RT21280140
28–
17
28
b. Remove 3 steering boot nuts (arrow) from the front
baffle plate, and then loosen the worm clamp (1) to
separate the steering boot from the front baffle plate.
(Tightening torque for nut: 10 ± 1 N·m)
(Tightening torque for worm clamp: 2 ± 0.5 N·m)
c. Remove the coupling bolt (arrow) between steering
column with intermediate shaft assembly and steering
gear input shaft.
(Tightening torque: 30 ± 3 N·m)
d. Remove 2 fixing nuts (arrow) from the upper bracket
of steering column assembly.
(Tightening torque: 25 ± 3 N·m)
e. Remove 2 fixing bolts (arrow) from the lower bracket
of steering column assembly.
(Tightening torque: 25 ± 3 N·m)
f. Carefully remove the steering column with intermediate shaft assembly.
1
RT21280170
RT21280180
RT21280150
RT21280160
CAUTION
DO NOT touch the interior ornament when removing the steering column with intermediate shaft
assembly to avoid scratching the interior ornament.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст