Chery Tiggo 5 (T21). Manual — part 93
06–
214
06
Diagnosis Procedure
a. Using a fuel pressure gauge, check fuel pressure (
Standard Fuel Pressure
a. Connect diagnostic tester, start the engine and select Read Datastream.
b. Observe if any speed signal is output.
a. Remove ignition coil and spark plug of one cylinder, and ground spark plug housing. Start the engine, and
check if spark is generated.
OK: Spark is generated.
a. Measure compression of misfiring cylinder (
Engine cranks normally but cannot start successfully while starting
1
Check fuel pressure
Condition
Fuel System Pressure (kPa)
Key ON
400
Engine Idling
400
Key LOCK
400
Repair or replace fuel system
NG
2
Using diagnostic tester, observe if any speed signal is output
OK
Check and repair crankshaft position
sensor wire harness
NG
3
Check spark
OK
Check and repair ignition system
NG
4
Check pressure of cylinder
OK
Check engine to confirm cause of low
compression
NG
OK
06–
215
06
a. Disconnect ECM connector E-033.
b. Turn ignition switch to ON and check ECM connector
terminals.
5
Check ECM power supply and ground
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065069
Multimeter
Connection
Condition
Specified
Condition
E-033 (35, 20) -
E-033 (63 or 64)
Ignition switch ON
11 to 14 V
Repair or replace related wire harness
NG
Go to Diagnostic Help
OK
06–
216
06
Diagnosis Procedure
a. Using a fuel pressure gauge, check fuel pressure (
Standard Fuel Pressure
a. Remove ignition coil and spark plug of one cylinder, and ground spark plug housing. Start the engine, and
check if spark is generated.
OK: Spark is generated.
Difficult to start with hot engine
1
Check fuel pressure
Condition
Fuel System Pressure (kPa)
Key ON
400
Engine Idling
400
Key LOCK
400
Repair or replace fuel system
NG
2
Check spark
OK
Check and repair ignition system
NG
3
Disconnect coolant temperature sensor connector, start engine and observe if engine starts
successfully at this time
OK
Check and repair wire harness or replace
sensor
OK
4
Check fuel pressure regulator
NG
Replace fuel pressure regulator
NG
OK
06–
217
06
a. Observe if trouble occurs just after fuel is filled.
a. Disconnect ECM connector E-033.
b. Turn ignition switch to ON and check ECM connector
terminals.
5
Check fuel condition
Replace fuel
NG
6
Check ECM power supply and ground
OK
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065069
Multimeter
Connection
Condition
Specified
Condition
E-033 (35, 20) -
E-033 (63 or 64)
Ignition switch ON
11 to 14 V
Repair or replace related wire harness
NG
Go to Diagnostic Help
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст