Chery Tiggo 5 (T21). Manual — part 94
06–
218
06
Diagnosis Procedure
a. Using a fuel pressure gauge, check fuel pressure (
Standard Fuel Pressure
a. Remove ignition coil and spark plug of one cylinder, and ground spark plug housing. Start the engine, and
check if spark is generated.
OK: Spark is generated.
Difficult to start with cold engine
1
Check fuel pressure
Condition
Fuel System Pressure (kPa)
Key ON
400
Engine Idling
400
Key LOCK
400
Repair or replace fuel system
NG
2
Check spark
OK
Check and repair ignition system
NG
3
Disconnect coolant temperature sensor connector, start engine and observe if engine starts
successfully at this time
OK
Check and repair wire harness or replace
sensor
OK
4
Depress accelerator pedal slightly, and observe if it is easy to start
NG
Clean throttle
OK
NG
06–
219
06
a. Observe if trouble occurs just after fuel is filled.
a. Measure compression of misfiring cylinder (
a. Disconnect ECM connector E-033.
b. Turn ignition switch to ON and check ECM connector
terminals.
5
Check injector for leakage or blockage
Clean or replace injector
NG
6
Check fuel condition
OK
Replace fuel
NG
7
Check pressure of cylinder
OK
Check engine to confirm cause of low
compression
NG
8
Check ECM power supply and ground
OK
E-033
49 50 51
63
64
15
16
31
32
47
48
33 34 35
17 18 19
1 2 3
52 53 54 55 56 57 58 59 60 61 62
36 37 38 39 40 41 42 43 44 45 46
20 21 22 23 24 25 26 27 28 29 30
4 5 6 7 8 9 10 11 12 13 14
-
+
V
RT21065069
Multimeter
Connection
Condition
Specified
Condition
E-033 (35, 20) -
E-033 (63 or 64)
Ignition switch ON
11 to 14 V
Repair or replace related wire harness
NG
Go to Diagnostic Help
OK
06–
220
06
Diagnosis Procedure
a. Using a fuel pressure gauge, check fuel pressure (
Standard Fuel Pressure
a. Check spark plug of each cylinder, and observe if the type and gap are as specified.
a. Remove ignition coil and spark plug of one cylinder, and ground spark plug housing. Start the engine, and
check if spark is generated.
OK: Spark is generated.
Engine speed is normal, but it is difficult to start at anytime
1
Check air filter for blockage, and intake pipe for air leakage
Check and repair intake system
NG
2
Check fuel pressure
OK
Condition
Fuel System Pressure (kPa)
Key ON
400
Engine Idling
400
Key LOCK
400
Repair or replace fuel system
NG
3
Check spark plug
OK
Replace spark plug
NG
4
Check spark
OK
Check and repair ignition system
NG
OK
06–
221
06
a. Observe if trouble occurs just after fuel is filled.
a. Measure compression of misfiring cylinder (
a. Check if engine ignition sequence and ignition timing are as specified.
5
Disconnect coolant temperature sensor connector, start engine and observe if engine starts
successfully at this time
Check and repair wire harness or replace
sensor
OK
6
Depress accelerator pedal slightly, and observe if it is easy to start
NG
Clean throttle
OK
7
Check injector for leakage or blockage
NG
Clean or replace injector
NG
8
Check fuel condition
OK
Replace fuel
NG
9
Check pressure of cylinder
OK
Check engine to confirm cause of low
compression
NG
10
Check engine ignition sequence and ignition timing
OK
Check and repair ignition timing
NG
OK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст