Chery Tiggo 5 (T21). Manual — part 111
07–
30
07
10.Remove the timing belt.
a. Remove the cylinder head cover (
).
b. Turn the camshaft, install the camshaft timing tool (1),
tighten the fixing bolts (arrow), and lock the exhaust
camshaft (2) and intake camshaft (3).
c. Remove the plug (arrow) for installing crankshaft
timing tool from the bottom of engine block.
(Tightening torque: 40 + 5 N·m)
d. Carefully screw in the crankshaft timing tool (arrow)
until the crankshaft is stuck completely.
481H
EX
481H
IN
RT21070110
1
2
3
CAUTION
After installing camshaft locking special tool, the crankshaft will be in the timing position, the camshaft
timing tool can be installed at this time.
RT21070120
RT21070130
CAUTION
This operation needs patience, and exercise extreme care not to damage the crankshaft.
When crankshaft is stuck completely, pistons in 4 cylinders of engine are at the same level.
07–
31
07
e. Remove the fixing bolt (arrow) from timing belt
tensioner, and remove the timing belt tensioner
assembly (1).
(Tightening torque: 20 + 5 N·m)
f. Remove the timing belt (2).
Inspection
1. Check timing belt.
If the timing belt has the following conditions, replace it.
a. There are cracks on the back of belt: as shown in the
illustration (1).
b. There are cracks at the bottom or cord fabric layer of
belt: as shown in the illustration (2), (3) and (5).
c. Belt worn: as shown in the illustration (6).
d. Belt teeth missing and damaged: as shown in the
illustration (4) and (6).
1
2
RT21070140
CAUTION
Check timing belt carefully before installation, and replace it to prevent any of the following symptoms.
RT21070150
1
2
4
3
6
5
CAUTION
Check timing belt carefully before installation. If any of above conditions occurs, replace the timing belt.
07–
32
07
2. Check timing belt tensioner assembly.
a. Rotate timing belt tensioner by hands and check if the
rotation is smooth and if abnormal noise occurs.
b. Wiggle timing belt tensioner in the axial and radial
direction to check if there is slackness.
c. Check if there is damage on the timing belt tensioner
surface.
Installation
1. Loosen the exhaust camshaft phaser assembly.
a. While holding the hexagon surface on exhaust
camshaft with an open wrench, loosen the exhaust
phaser cover (1) with a torque wrench in the direction
of arrow as shown in the illustration.
(Tightening torque: 30 N·m)
b. Remove the exhaust phaser cover.
c. While holding the hexagon surface on exhaust
camshaft with an open wrench, loosen the fixing bolt
of exhaust camshaft phaser assembly (1) with a
torque wrench in the direction of arrow as shown in
the illustration.
(Tightening torque: 120 ± 5 N·m)
3159B
5/8
13
RT21070160
1
RT21070170
RT21070171
1
CAUTION
Loosen exhaust camshaft phaser assembly without removing it.
07–
33
07
2. Loosen the intake camshaft phaser assembly.
a. While holding the hexagon surface on intake camshaft
with an open wrench, loosen the intake phaser cover
(1) with the monkey wrench in the direction of arrow
as shown in the illustration.
(Tightening torque: 30 N·m)
b. Remove the intake phaser cover.
c. While holding the hexagon surface on intake camshaft
with an open wrench, loosen the fixing bolt of intake
camshaft phaser assembly (1) with a torque wrench in
the direction of arrow as shown in the illustration.
(Tightening torque: 120 ± 5 N·m)
3. Install the timing belt.
HINT:
Install the timing belt and be sure that the exhaust
camshaft phaser assembly (1), intake camshaft phaser
assembly (2), crankshaft timing belt pulley (7) and
coolant pump pulley (6) are at inside of timing belt tooth.
Also, the timing belt tensioner (5), contacting idler pulley
(3) and timing belt idler pulley (4) are at outside of tooth.
4. Install the timing belt tensioner.
a. Install the fixing bolt to timing belt tensioner by hand, and do not tighten the fixing bolt of timing belt
tensioner.
1
RT21070180
RT21070181
1
CAUTION
Loosen intake camshaft phaser assembly without removing it.
1
5
7
3
2
4
6
RT21070190
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст