Chery Tiggo 5 (T21). Manual — part 277
25–
41
25
g. Connect the negative battery cable.
h. Turn ignition switch ON.
i. Using a digital multimeter, measure the voltage between
connector E-085 and body ground to check if the front
right wheel speed sensor is short to power supply
according to the table below.
Standard Voltage
a. Use X-431 3G diagnostic tester to clear the DTC.
b. Start the engine.
c. Drive the vehicle at 15 km/h or more, read the ABS control module assembly DTC again with X-431 3G
diagnostic tester.
d. Check if the same DTC is output.
RT21250280
E-085
13
12 11 10 9 8 7 6 5 4 3 2
24 23 22 21 20 19 18 17 16 15 14
37 36 35 34 33 32 31 30 29 28 27 26
1
38
25
-
+
V
Multimeter
Connection
Condition
Specified
Condition
E-085 (4) - Body
ground
Ignition switch ON Approximately 0 V
E-085 (16) - Body
ground
Ignition switch ON Approximately 0 V
Repair or replace wire harness and
connector between front right wheel
speed sensor and ABS control module
assembly
NG
6
Reconfirm DTCs
OK
System operates normally
NO
Replace ABS control module assembly
YES
25–
42
25
DTC
C0037-00 Left Rear Wheel Speed Sensor
DTC
C0037-09 Left Rear Wheel Speed Sensor
DTC
C0037-11 Left Rear Wheel Speed Sensor
DTC
C0037-12 Left Rear Wheel Speed Sensor
DTC
C0037-13 Left Rear Wheel Speed Sensor
DTC
C0037-29 Left Rear Wheel Speed Sensor
25–
43
25
ET21250080
BATTERY
ABS
CONTROL
MODULE
IGNITION SWITCH
ON OR START
EF47
25A
I1
A10
1
25
28
MF01
40A
EF34
20A
EF36
10A
ENGINE
COMPARTMENT
FUSE AND
RELAY BOX
R
RL
R
13
12 11 10 9 8 7 6 5 4 3 2
24 23 22 21 20 19 18 17 16 15 14
37 36 35 34 33 32 31 30 29 28 27 26
1
38
25
Gr
E-074
Gr
E-076
A1
A2
A3
A4
A5
A6
A7
A8 A9 A10
I2
I1
E-074
E-076
B
E-085
E-085
38
13
Br
B
E-042
31
18
2
1
REAR LEFT
WHEEL SPEED
SENSOR
GR
GW
GR
GW
9
20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
2
1
W
E-029
B-054
E-029
B
B-029
B-029
25–
44
25
Diagnosis Procedure
a. Turn ignition switch to LOCK.
b. Disconnect the negative battery cable.
c. Disconnect the rear left wheel speed sensor connector B-029.
d. Check if the wire harnesses are worn, pierced, pinched or partially broken.
e. Look for broken, bent, protruded or corroded terminals.
f. Check if related connector pins are in good condition.
DTC Code
DTC Definitions
DTC Detection
Conditions
Possible Cause
C0037-00
Left Rear Wheel Speed
Sensor
These DTCs occur
when any of the
following conditions is
met:
1. ABS control module
assembly detects
that the wheel
speed sensor signal
wire is short to
ground.
2. Wheel speed sensor
line is open.
3. ABS control module
assembly detects
that the wheel
speed sensor signal
wire is short to
power supply.
4. ABS control module
assembly detects
that the wheel
speed sensor power
supply wire is short
to ground.
5. Wheel speed sensor
signal is invalid.
Wheel speed sensor signal wire is
connecting with the power supply wire
in reverse.
Wheel speed sensor signal wire is
short to ground.
Wheel speed sensor line is open,
connector is loose or broken.
Wheel speed sensor signal wire is
short to power supply.
Wheel speed sensor power supply
wire is short to ground.
Sensor head or plug pin is damaged.
Wheel speed sensor is interfered by
magnetic field outside (wheel or axle is
not demagnetized).
Wheel speed sensor body is
malfunctioning.
Ring gear is not installed, has teeth
missing, dirty, demagnetized or off
center.
Clearance between sensor and ring
gear is excessive.
Number of ring gear teeth is wrong.
Tire size is not as specified.
ABS control module assembly is
damaged.
C0037-09
Left Rear Wheel Speed
Sensor
C0037-11
Left Rear Wheel Speed
Sensor
C0037-12
Left Rear Wheel Speed
Sensor
C0037-13
Left Rear Wheel Speed
Sensor
C0037-29
Left Rear Wheel Speed
Sensor
CAUTION
When performing electrical equipment diagnosis and test, always refer to the circuit diagram for related
circuit and component information.
1
Check rear left wheel speed sensor wire harness and connector
Repair or replace rear left wheel speed
sensor wire harness and connector
NG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст