Chery Tiggo 5 (T21). Manual — part 362
32–
39
32
DTC
B0072-11
Belt Pretensioner Front Passenger Loop Circuit Short to
Ground
DTC
B0072-12
Belt Pretensioner Front Passenger Loop Circuit Short to
Battery
DTC
B0072-1A
Belt Pretensioner Front Passenger Loop Circuit
Resistance Below Threshold
DTC
B0072-1B
Belt Pretensioner Front Passenger Loop Circuit
Resistance Above Threshold
DTC
B0072-1C
Belt Pretensioner Front Passenger Loop Circuit Voltage
Out of Range
32–
40
32
ET21320070
16 15 14 13 12 11 10
8
7
6
5
4
3
2
1
9
W
I-036
32
31
30
29
28
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
27
26
25
24
23
22
21
20
19
18
17
Gr
I-046
SRS
CONTROL
MODULE
I-046
IGNITION SWITCH
ON OR START
10A
RF08
INSTRUMENT
PANEL FUSE
AND RELAY BOX
I-007
B
I-045
16
1
2
3
4
5
6
7
8
9 10 11 12
13
85
85
87
87 30
87 30
30
86
86
85
86
14 15 16 17 18 19 20 21 22 23 24
25
27
26
B
I-007
VW
VW
V
V
-
+
1
2
8
7
1
2
1
2
-
+
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
FRONT
PASSENGER
SEAT BELT
PRE-TENSIONER
B-002
B
B-002
W
I-006
I-006
B-003
8
R
R
1
4
I-036
B-055
*2
*1
B-072
*2: SRS control module connector is B-072
*1: SRS control module connector is I-046
B
B-072
32–
41
32
Self-diagnosis Detection Logic
HINT:
When performing electrical diagnosis and test, always refer to the relevant circuit diagram for the special
circuit and component information.
Diagnosis Procedure
a. Turn ignition switch to LOCK, disconnect the negative battery cable and wait for at least 90 seconds.
b. Disconnect front passenger seat belt pretensioner connector, and connect the new front passenger seat
belt pretensioner connector to connector B-002.
c. Reconnect the negative battery cable and wait for a few seconds.
d. Turn ignition switch ON and wait for at least 90 seconds.
e. Use X-431 3G diagnostic tester to clear the DTCs.
f. Turn ignition switch to LOCK.
g. Turn ignition switch ON and wait for at least 90 seconds.
h. Use X-431 3G diagnostic tester to check if the DTCs are still output.
DTC Code
DTC Definition
DTC Detection
Condition
Warning Light
Condition
Possible Cause
B0072-11
Belt Pretensioner Front
Passenger Loop
Circuit Short to Ground
Ignition switch ON
ON
Front passenger
seat belt
pretensioner
Wire harness and
connector
SRS control
module assembly
B0072-12
Belt Pretensioner Front
Passenger Loop
Circuit Short to Battery
B0072-1A
Belt Pretensioner Front
Passenger Loop
Circuit Resistance
Below Threshold
B0072-1B
Belt Pretensioner Front
Passenger Loop
Circuit Resistance
Above Threshold
B0072-1C
Belt Pretensioner Front
Passenger Loop
Circuit Voltage Out of
Range
1
Check front passenger seat belt pretensioner
WARNING
Never measure the front passenger seat belt pretensioner directly, otherwise, it may cause serious
personal injury due to accidental deployment of the airbag.
Replace front passenger seat belt
pretensioner
NG
32–
42
32
Use circuit diagram as a guide to perform the following procedures:
a. Turn ignition switch to LOCK, disconnect the negative battery cable and wait for at least 90 seconds.
b. Disconnect the front passenger seat belt pretensioner connector B-002 and SRS control module assembly
connector I-046/B-072.
c. Disconnect the body wire harness connector B-003 and instrument panel wire harness connector I-006
(*1).
d. Check if wire harnesses are worn, pierced, pinched or partially broken.
e. Check for broken, bent, protruded or corroded terminals.
f. Check if related connector terminal contact pins are in good condition.
a. Turn ignition switch to LOCK, disconnect the negative
battery cable and wait for at least 90 seconds.
b. Disconnect the SRS control module assembly connector
I-046/B-072.
c. Disconnect the front passenger seat belt pretensioner
connector B-002.
d. Connect the negative battery cable and wait for a few
seconds.
e. Turn ignition switch ON.
f. Using a digital multimeter, measure the voltage between
front passenger seat belt pretensioner connector B-002
and body ground to check for a short circuit to power
supply according to the table below.
Standard Voltage
2
Check wire harness and connector
OK
Repair or replace instrument panel/body
wire harness and connector
NG
3
Check front passenger seat belt pretensioner control circuit
OK
RT21320280
-
+
V
1
2
-
+
B-002
Multimeter
Connection
Condition
Specified
Condition
B-002 (1) - Body
ground
Ignition switch ON
Below 1 V
B-002 (2) - Body
ground
Ignition switch ON
Below 1 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст