Chery Tiggo 5 (T21). Manual — part 364

32–

47

32

ET21320080

32

31

30

29

28

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

27

26

25

24

23

22

21

20

19

18

17

Gr

I-046

SRS
CONTROL
MODULE

I-046

IGNITION SWITCH

ON OR START

10A

RF08

INSTRUMENT
PANEL FUSE
AND RELAY BOX

I-007

B

I-045

16

1

2

3

4

5

6

7

8

9 10 11 12

13

85

85

87

87 30

87 30

30

86

86

85

86

14 15 16 17 18 19 20 21 22 23 24

25

27

26

B

I-007

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

W

I-006

BR

BR

B

B

B

1

2

20

15

I-045

11

FRONT
PASSENGER
SEAT BELT
SWITCH

1

2

I-006

B

B-050

B-050

B-003

I-006

B-003

8

R

R

1

4

I-036

B-055

*2

B-072

16 15 14 13 12 11 10

8

7

6

5

4

3

2

1

9

W

I-036

*2: SRS control module connector is B-072

*1: SRS control module connector is I-046

B

B-072

*1

32–

48

32

Self-diagnosis Detection Logic

HINT:
When performing electrical diagnosis and test, always refer to the relevant circuit diagram for the special
circuit and component information.

Diagnosis Procedure

a. Turn ignition switch to LOCK, disconnect the negative battery cable and wait for at least 90 seconds.
b. Disconnect front passenger seat belt switch connector, and connect the new front passenger seat belt

switch connector to connector B-050.

c. Reconnect the negative battery cable and wait for a few seconds.
d. Turn ignition switch ON and wait for at least 90 seconds.
e. Use X-431 3G diagnostic tester to clear the DTCs.
f. Turn ignition switch to LOCK.
g. Turn ignition switch ON and wait for at least 90 seconds.
h. Use X-431 3G diagnostic tester to check if the DTCs are still output.

Use circuit diagram as a guide to perform the following procedures:
a. Turn ignition switch to LOCK, disconnect the negative battery cable and wait for at least 90 seconds.
b. Disconnect the front passenger seat belt switch connector B-050 and SRS control module assembly

connector I-046/B-072.

c. Disconnect the body wire harness connector B-003 and instrument panel wire harness connector I-006

(*1).

d. Check if wire harnesses are worn, pierced, pinched or partially broken.
e. Check for broken, bent, protruded or corroded terminals.
f. Check if related connector terminal contact pins are in good condition.

DTC Code

DTC Definition

DTC Detection

Condition

Warning Light

Condition

Possible Cause

B1231-12

Buckle Switch Front
Passenger (BLFP)
Circuit Short to Battery

Ignition switch ON

ON

 Front passenger

seat belt switch

 Wire harness and

connector

 SRS control

module assembly

B1231-1C

Buckle Switch Front
Passenger (BLFP)
Circuit Voltage Out of
Range

1

Check front passenger seat belt switch

Replace front passenger seat belt switch

NO

2

Check wire harness and connector

YES

Repair or replace instrument panel/body
wire harness and connector

NG

32–

49

32

a. Turn ignition switch to LOCK, disconnect the negative

battery cable and wait for at least 90 seconds.

b. Disconnect the front passenger seat belt switch

connector B-050 and SRS control module assembly
connector I-046/B-072.

c. Connect the negative battery cable and wait for a few

seconds.

d. Turn ignition switch ON.
e. Using a digital multimeter, measure the voltage between

front passenger seat belt switch connector B-050 and
body ground to check for a short circuit to power supply
according to the table below.
Standard Voltage

f. Turn ignition switch to LOCK, disconnect the negative

battery cable and wait for at least 90 seconds.

g. Using a digital multimeter, check for continuity between

front passenger seat belt switch connector B-050 and
body ground to check for a short circuit to ground
according to the table below.
Standard Condition

3

Check front passenger seat belt switch control circuit

OK

RT21320320

-

+

V

1

2

B-050

Multimeter

Connection

Condition

Specified

Condition

B-050 (1) - Body

ground

Ignition switch ON

Below 1 V

-

+

RT21320330

1

2

B-050

Multimeter

Connection

Condition

Specified

Condition

B-050 (1) - Body

ground

Always

No continuity

Replace SRS control module assembly

OK

NG

32–

50

32

a. Turn ignition switch to LOCK, disconnect the negative

battery cable and wait for at least 90 seconds.

b. Disconnect the instrument panel wire harness connector

I-006 and SRS control module assembly connector I-046/
(*1).

c. Using a digital multimeter, check for continuity between

the terminals of connector I-006 and connector I-046
according to the table below.
Standard Condition

a. Turn ignition switch to LOCK, disconnect the negative

battery cable and wait for at least 90 seconds.

b. Disconnect front passenger seat belt switch connector B-

050 and SRS control module assembly connector I-046/
B-072.

c. Using a digital multimeter, check for continuity between

the terminals of connector B-050 and connector I-046/B-
072 according to the table below.
Standard Condition

4

Check front passenger seat belt switch wire harness and connector (SRS control module
assembly - instrument panel wire harness connector)

-

+

RT21320340

32

31

30

29

28

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

27

26

25

24

23

22

21

20

19

18

17

I-046

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

I-006

Multimeter

Connection

Condition

Specified

Condition

I-006 (15) - I-046

(20)

Always

Continuity

Replace instrument panel wire harness
and connector

NG

5

Check wire harness and connector (SRS control module assembly - front passenger seat
belt switch)

OK

-

+

RT21320341

32

31

30

29

28

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

27

26

25

24

23

22

21

20

19

18

17

B-072

I-046

1

2

B-050

Multimeter

Connection

Condition

Specified

Condition

B-050 (1) - I-046/

B-072 (20)

Always

Continuity

Replace body wire harness and connector

NG