Chery Tiggo 5 (T21). Manual — part 113

07–

38

07

Installation

1. Install the camshaft oil seal.

HINT:

 Use the same installation procedures for the exhaust camshaft oil seal and intake camshaft oil seal.

 Procedures listed below are for intake camshaft oil seal.
a. Using a special tool (camshaft oil seal installer) (1),

install the intake camshaft oil seal (2) to intake
camshaft (3).

2. Other installation procedures are in the reverse order of removal.

CAUTION

 Remove the dirt on oil seal retainer and apply a coat of engine oil to the oil seal retainer and oil seal lip

before installation.

 Be sure to prevent the lip of camshaft oil seal from being scratched during installation. If it is damaged,

replace immediately.

RT21070240

1

2

3

07–

39

07

Crankshaft Front Oil Seal

Removal

1. Turn off all the electrical equipment and ignition switch.
2. Disconnect the negative battery cable.
3. Remove the engine trim cover assembly (

See page 10-10

).

4. Remove the engine lower right protector assembly (

See page 48-29

).

5. Remove the accessory drive belt (

See page 07-24

).

6. Remove the belt tensioner assembly (

See page 07-27

).

7. Use an engine equalizer to hang the engine right lifting eye.
8. Remove the engine right mounting (

See page 07-68

).

9. Remove the engine timing belt (

See page 07-28

).

10.Remove the crankshaft timing pulley.

a. Loosen the crankshaft timing pulley fixing bolt (arrow).



(Tightening torque: 1st step: tighten to 130 ± 10 N·m;
2nd step: retighten by 65° ± 5°)

HINT:
Shift the transmission into 5th gear (for MT model) or
D position (for CVT model) when loosening the
crankshaft timing gear fixing bolt to engage the
crankshaft and propeller shaft. Another technician
depresses the brake pedal, which can lock the
crankshaft by mechanical gear train.

b. Remove the timing pulley fixing bolt (1), washer (2),

crankshaft timing pulley (3), lining (4) and semi-circle
key (5) in order.

CAUTION

 Be sure to wear necessary safety equipment to prevent accidents when repairing.
 Try to prevent body paint surface from being scratched during removal and installation.

RT21070250

RT21070260

4

1

5

3

2

CAUTION

 Semi-circle key is small, so it is easy to be ignored. During installation, pay thorough attention not to

forget to install.

07–

40

07

11.Remove the crankshaft front oil seal.

a. Using a flat tip screwdriver wrapped with tape, pry out

the crankshaft front oil seal (1) carefully.

Installation

1. Remove the dirt around the crankshaft front oil seal

retainer and on its inner wall.

2. Install the crankshaft front oil seal guide tool (3) to the

crankshaft (4).

3. Install the new oil seal (2) to the crankshaft front oil seal

guide tool, and install the new oil seal to the oil seal
retainer completely with a crankshaft front oil seal
installer (1).

4. Install the lining (4).
5. Using a brass bar, install the semi-circle key (5) in place.

HINT:
Protrusion height of semi-circle key should be 2.2 - 2.3
mm.

6. Install the crankshaft timing pulley (3), washer (2) and

bolt (1) in order.

RT21070270

1

CAUTION

 Be careful not to damage the oil seal retainer and surface of crankshaft when removing crankshaft front

oil seal.

CAUTION

 Apply a coat of engine oil to crankshaft front oil seal guide tool before installing the new oil seal.
 Remove the dirt on oil seal retainer and apply a coat of engine oil to oil seal retainer and oil seal lip

before installation.

 Be sure to prevent the lip of crankshaft front oil seal from being scratched during installation. If it is

damaged, replace immediately.

RT21070280

1

2

3

4

RT21070260

4

1

5

3

2

07–

41

07

7. Tighten the crankshaft timing pulley fixing bolt (arrow).



(Tightening torque: 1st step: tighten to 130 ± 10 N·m; 2nd
step: retighten by 65° ± 5°)

8. Other installation procedures are in the reverse order of removal.

RT21070250