Chery Tiggo. Manual — part 163
10.
CHECK INJECTOR RESISTANCE
• Check resistance as table shown.
• Check the fuel injector resistance as shown in the following:
INJECTOR
NO.
INJECTOR
TERMINAL
RESISTANCE
(APPROXIMATELY)
⍀ (20°C)
1
1 & 2
11 - 16
2
1 & 2
3
1 & 2
4
1 & 2
• Connect ECM connector.
• Connect injector connector.
• Check the fuel injector voltage as shown in the following:
TERMINAL NO.
ITEM
CONDITION
DATA (AVERAGE DC
VOLTAGE)
6
Injector 2
• Engine is running
• Warm-up condition
• Idle
• Accelerate suddenly
Voltage: 11 - 14 V
7
Injector 3
27
Injector 1
47
Injector 4
Is the check result normal?
Yes
>>
Go to the next step.
No
>>
Replace injector.
11.
CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• See ⬙DTC Confirmation Procedure⬙.
Is DTC P0261, P0264, P0267 or P0270 still present?
Yes
>>
Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>
The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03
P0262 - Cylinder 1 Injector Circuit High
P0265 - Cylinder 2 Injector Circuit High
P0268 - Cylinder 3 Injector Circuit High
P0271 - Cylinder 4 Injector Circuit High
DIAGNOSIS & TESTING
LTSMW030029T
DIAGNOSIS & TESTING
LTSMW030030T
03
Check reference values between ECM terminals and ground under the following conditions:
ECM TERMINAL NO.
ITEM
CONDITION
DATA (AVERAGE DC
VOLTAGE)
6
Injector 2
• Engine is running
• Warm-up condition
• Idle
• Accelerate suddenly
Voltage: 11 V - 14 V
7
Injector 3
27
Injector 1
47
Injector 4
On Board Diagnostic Logic
• Self-diagnosis detection logic.
DTC NO.
DTC DEFINITION
DTC DETECTION
CONDITION
POSSIBLE CAUSE
P0262
Cylinder 1 - Injector Circuit
High
Engine is running
• Injector
• Harness or connectors
• ECM
P0265
Cylinder 2 - Injector Circuit
High
P0268
Cylinder 3 - Injector Circuit
High
P0271
Cylinder 4 - Injector Circuit
High
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it to normal operating temperature then select view DTC.
• If DTC is detected, go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnosis & Testing Diagnostic Help in Sec-
tion 03 Electronic Engine Controls).
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
Diagnostic Procedure
1.
CHECK GROUND CONNECTIONS
• Turn ignition switch off.
• Loosen and retighten ground screws on the body (See Ground Inspection in Section 03 Electronic Engine Con-
trols).
• Inspect ground connections E-207 and E-208 mounting position (See Vehicle Wiring Harness Layout - Engine
Room Harness (With 2.0L Engine) in Section 16 Wiring).
Are the ground connections OK?
Yes
>>
Go to the next step.
No
>>
Repair or replace ground harness or connections.
DIAGNOSIS & TESTING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст