Chery Tiggo. Manual — part 326
ON-VEHICLE SERVICE
Front Intermediate Drive Shaft
Removal & Installation
1. Remove the bolts (1) between the front intermedi-
ate drive shaft and the ITM Controller input shaft.
(Tighten: Front intermediate drive shaft and ITM
controller bolts to 70 ± 7 N·m)
2. Installation is in the reverse order of removal.
Rear Intermediate Drive Shaft
Removal & Installation
1. Remove the bolts between the rear intermediate drive shaft and the ITM Controller output shaft.
(Tighten: Rear intermediate drive shaft and ITM controller bolts to 39 ± 3 N·m)
2. Remove the bolts between the intermediate drive shaft bracket and the vehicle body, and then remove the
bracket.
(Tighten: Rear intermediate drive shaft to body bolts to 60 ± 5 N·m)
3. Remove the bolts (1) between the rear intermedi-
ate drive shaft and the rear axle flange, and
remove the rear intermediate drive shaft.
(Tighten: Rear intermediate drive shaft and rear
axle flange bolts to 65 ± 6 N·m)
4. Installation is in the reverse order of removal.
LTSM160020
LTSM160021
09
SUSPENSION
10
CONTENTS
page
Front Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Rear Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-25
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-38
Wheels and Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-47
FRONT SUSPENSION
GENERAL INFORMATION
10-2
Description
10-2
Operation
10-4
Specifications
10-4
Special Tools
10-5
DIAGNOSIS & TESTING
10-6
Vehicle Suspension Troubleshooting Chart
10-6
ON-VEHICLE SERVICE
10-7
Front Steering Knuckle
10-7
Description
10-7
Operation
10-7
Removal & Installation
10-7
Front Lower Control Arm
10-9
Description
10-9
Operation
10-9
Removal & Installation
10-9
Front Stabilizer Bar Link
10-11
Removal & Installation
10-11
Front Stabilizer Bar
10-12
Removal & Installation
10-12
Front Strut Assembly
10-13
Description
10-13
Operation
10-14
Diagnosis & Testing
10-14
Removal & Installation
10-14
Front Coil Spring
10-16
Description
10-16
Operation
10-16
Removal & Installation
10-16
Front Sub-Frame Assembly
10-17
Removal & Installation
10-17
UNIT REPAIR
10-21
Front Strut
10-21
Disassemble
10-21
Inspection
10-22
Strut Disposal Procedure
10-22
Assembly
10-23
10
GENERAL INFORMATION
Description
The front suspension system incorporates a strut assembly that takes the place of the upper control arm and upper
ball joint. The strut carries out the function of a shock absorber and is encompassed by a coil spring. The strut
assembly supports the weight of the vehicle and is also the pivot point for the steering knuckle. This system uses a
lower control arm and ball joint for the lower pivot point of the steering knuckle.
The front suspension consists of the following components:
GENERAL INFORMATION
LTSM100008
10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст