Chery Tiggo. Manual — part 149
6.
CHECK DTC
• With the X-431 scan tool, read ECM DTCs.
• Refer to ⬙DTC Confirmation Procedure⬙.
Is DTC P0118 still present?
Yes
>>
Replace the ECM.
NOTE : The Immobilizer control module must be matched to the new ECM (See ECM Removal & Instal-
lation in Section 03 Electronic Engine Controls).
No
>>
The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
03
P0122 - Throttle Position Sensor A Circuit Low Input
DIAGNOSIS & TESTING
LTSMW030025T
Check reference values between ECM terminals and ground under the following conditions:
ECM TERMINAL
NO.
ITEM
CONDITION
DATA (DC
VOLTAGE)
32
Regulated sensor
supply
Ignition switch: ON
-
Approximately 5 V
38
Electronic throttle
control actuator
(position sensor)
• Engine stopped
• Accelerator pedal:
Fully released
4.24 V
• Engine stopped
• Accelerator pedal:
Fully depressed
0.72 V
54
Electronic throttle
control actuator
• Engine stopped
• Accelerator pedal:
Fully released
0.74 V
• Engine stopped
• Accelerator pedal:
Fully depressed
4.62 V
64
Motor 4
-
12 V or 0 V
65
Motor 3
66
Motor 2
12 V or 0 V
67
Motor 1
78
Sensor (GND)
Approximately 0 V
On Board Diagnostic Logic
• Self-diagnosis detection logic.
DTC NO.
DTC DEFINITION
DTC DETECTION
CONDITION
DTC SET
CONDITION
POSSIBLE CAUSE
P0122
Throttle position
sensor A circuit low
input
• Ignition switch:
ON
• Engine: Running
Signal output is
below minimum
acceptable range for
a few seconds
continuously.
• TPS or
misalignment
• Harness or
connectors
• ECM
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Turn ignition switch off.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on.
• With the scan tool, record and erase stored DTCs in the ECM.
• Start engine and warm it to normal operating temperature, then select view DTC and data stream.
• If the DTC is detected, the DTC condition is current. Go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnostic Help and Intermittent DTC Trou-
bleshooting in Section 03 Electronic Engine Controls for more information.
NOTE :
While performing electrical diagnosis & testing, always refer to the electrical schematics for specific circuit
and component information.
DIAGNOSIS & TESTING
03
Diagnostic Procedure
1.
CHECK GROUND CONNECTIONS
• Turn ignition switch off.
• Loosen and retighten ground screws on the body (See Ground Inspection in Section 03 Electronic Engine Con-
trols).
• Inspect ground connections E-207 and E-208 mounting position (See Vehicle Wiring Harness Layout - Engine
Room Harness (With 2.0L Engine) in Section 16 Wiring).
Are the ground connections OK?
Yes
>>
Go to the next step.
No
>>
Repair or replace ground harness or connections.
2.
CHECK TPS SENSOR ELECTRICAL CONNECTOR
• Disconnect the TPS electrical connector (1).
• Inspect the electrical connector for damage.
Is the electrical connector OK?
Yes
>>
Go to the next step.
No
>>
Repair or replace the electrical connector
as necessary.
DIAGNOSIS & TESTING
VISMD030203
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст