Chery Tiggo. Manual — part 321
7. Remove the bolts (1) connecting the steering
knuckle to the front strut assembly.
CAUTION:
When removing the front axle shaft, do not
subject the constant velocity joint to an exces-
sive angle. Also, be careful not to excessively
extend the slide joint.
8. Remove the front axle shaft from the transaxle
using a suitable tool.
9. Installation is in the reverse order of removal.
Installation Notes:
• Rotate the joint up/down, left/right, and in axial direction, check for any rough movement or significant loose-
ness.
• Check boot for cracks or other damage, and for grease leakage.
• If damaged, disassemble axle shaft to verify damage, and repair or replace as necessary.
ON-VEHICLE SERVICE
LTSM100041
09
REAR AXLE
GENERAL INFORMATION
09-9
Description
09-9
Operation
09-9
Specifications
09-10
Special Tools
09-10
DIAGNOSIS & TESTING
09-11
Vehicle Inspection
09-11
Shudder Or Vibration During Acceleration
09-11
Vehicle Inspection
09-11
Noise Or Vibration On Turns
09-11
Clunking Noise During Acceleration
09-11
Shudder Or Vibration During Acceleration
09-11
Vibration At High Speeds
09-11
Visual Inspection For Fluid Leaks (4x4)
09-11
ON-VEHICLE SERVICE
09-12
Rear Hub and Bearing
09-12
Removal & Installation
09-12
Rear Axle Assembly (4x4)
09-13
Description
09-13
Operation
09-14
Removal & Installation
09-14
09-15
GENERAL INFORMATION
Description
The rear axle utilizes an independent design. This suspension system incorporates a separate wheel knuckle for
each wheel and allows the wheels to react to road imperfections independent of each other. This independent action
offers improved isolation from the effects of jounce and rebound.
The rear axle consists of the following components:
• Wheel Hub
• Wheel Studs
• Wheel Bearing
• Rear Trailing Arm
For further information on the rear axle assembly see Rear Suspension Description & Operation in Section 10 Sus-
pension.
Operation
The rear axle utilizes a sealed wheel bearing housed in the rear knuckle assembly.
Rear Axle
1 - Rear Sub-Frame Assembly
2 - Rear Suspension Upper Link
3 - Left Rear Shock Absorber Mounting Bracket
4 - Left Brake Line Bracket
5 - Left Rear Trailing Arm
6 - Rear Stabilizer Bar
7 - Left Rear Lower Control Arm
8 - Left and Right Stabilizer Bar Links
9 - Right Rear Connecting Rod
10 - Right Rear Lower Control Arm
11 - Rubber Support Seat
12 - Rear Stabilizer Bar
13 - Rubber Bushing
14 - Right Rear Trailing Arm
LTSM090005
09
Specifications
Torque Specifications
DESCRIPTION
TORQUE (N·m)
Rear Stabilizer Bar Link
40 - 50
Rear Shock Absorber to Mounting Bracket Bolts
40 - 50
Rear Axle Front Suspension to Rear Driving Axle Bolts
75 - 85
Rear Axle Front Suspension to Rear Sub-Frame Bolts
115 - 125
Left and Right Rear Half-Shaft to Disc Brake Nut
260 - 270
Left and Right Rear Half-Shaft to Axle Output Flange
Bolts
40
Intermediate Drive Shaft to Rear Axle Flange Bolts
59 - 71
Rear Axle Rear Suspension Mount Assembly to Rear
Axle Bolt
75 - 85
Rear Axle Rear Suspension Mount to Vehicle Body Bolt
75 - 85
Rear Rubber Buffer to Vehicle Body Bolts
22 - 28
Upper Link to Rear Sub-Frame Bolts
100 - 120
Lower Control Arm to Rear Sub-Frame Bolts
100 - 120
Rear Trailing Arm to Vehicle Body Bolts
140 - 160
Rear Suspension to Bracket Bolts
115 - 125
Rear Suspension, Longitudinal Beam of Engine to
Sub-Frame Bolts
75 - 85
Rear Stabilizer Bar Clamp to Vehicle Body Bolts
22 - 28
Rear Trailing Arm to Vehicle Body Bolts
140 - 160
Rear Cover of Control Arm to Sub-Frame Bolts
170 - 190
Soft Gasket to Bracket Of Rear Suspension Bolts
110 - 130
Sub-Frame And Gasket Of Vehicle (Rear) Body Bolts
170 - 190
Wheel Mounting Nut 110
Special Tools
Bearing Puller
GENERAL INFORMATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст