Chery S11 / Chery QQ. Manual — part 66

Chery QQ Service Manual BCM Computer Control System

Horn button wiring broken or loose contact

thereof

Repair or replace

The sound of horn is

low

Insufficient charge of secondary cell

Horn defective

Interference between horn and direction

indicator lamp

Recharge or change the

cell

Replace

Adjust

After releasing the horn

button, the horn would

not stop

Short in the horn button

Replace

Repair

Ⅲ

. Inspection and Repair of the Defrost System

In figure defrost system is schematically shown.

Schematic view of the defrost system

1、Inspection of the conduction of the defroster switch

As shown in the table, if it does not conform to the table, change the defroster

switch.

Inspection of the defroster switch

Switch position

Connection to the

instrument

Conductance

Switch OFF

-

No

- 108 -

Chery QQ Service Manual BCM Computer Control System

Switch ON

1-2

Yes

2、Inspection of defroster wiring

While cleaning the window, wipe with soft cloth along the line, don’t damage the

defroster wiring. Don’t use cleaning agent or cleaning device, otherwise the surface will

be damaged. While inspecting the voltage, insert the negative probe in an end of the

thermal fin, and push the wiring with finger as shown.

Inspection of voltage

Turn the start-up switch to ON, turn the defroster switch to ON, check the voltage at the

midpoints of each wire as shown. If the wire is broken, there is a voltage of about 10v

between the positive terminal of the meter and the midpoints of the wire, there is no

voltage between earth and the midpoints of wire.

Voltage State

About 5V

Normal

About 10V or 0V

Broken

Inspection of voltage of midpoint of the defroster wire

- 109 -

Chery QQ Service Manual BCM Computer Control System

Connect the positive probe of the Voltage meter to positive terminal of the defroster,

negative probe to the earth end. Press the positive probe on the hot wire and move it to

the negative terminal. If the voltage springs from 0V to some V at some point, this point

is the broken point, as shown in the figure. If the defroster wiring is not broken, at the

positive terminal of the defroster wiring the volt meter shows 0V, and during the probe

move to the other terminal, the voltage increases gradually to 12V.

Detection of the broken point of the defroster wiring

3、Repairing of the defroster wiring

Eliminate the tool cleaning broken point with lubricating grease (wax) and organosilicon,

during the repairing, attach adhesive tape on the both side of the defroster wiring. After

mixing of the repairing agent, drop the repairing agent to the broken point in appropriate

amount with electric brush. Remove the adhesive tape after few minutes, as shown in the

figure

Repairing of the defroster wiring

Ⅳ

. Inspection and Repair of Control System of Power Windows

1. Operating mode of power windows

- 110 -

Chery QQ Service Manual BCM Computer Control System

（1）

the function

of

power windows timer

①

After the start-up switch shut off, the power windows are operable within 30 seconds.

If the doors are opened or closed in the period, the power windows can be operated

within another 30 seconds.

②

During lowering the power window, if an overload is detected, the power windows

are operable within 30 secs.

③

Within the last 6 seconds of above-mentioned period, if the door window switch is

hold upwards for over 0.3 second, the door window then works in overloaded state to

prevent that the door window stops in opened state.

（

2）The function of power windows

①

operating condition

In the ON state of the start-up switch, after the start-up switch is turned off(the

operating time of the power window timer is within 30s)

②

operating progress

The power window switch is actuated for over 0.3s, the door window rises and lowers

automatically. During its operating, if the power window switch is actuated once again,

the door window stops.

③

stop conditions of the door windows

A. If the current through the door window motor is higher than 14.5A+1A, the door

window stops after 0.7s operating time.

B. After operating for 6s (required by raising and lowering the door window), the

operating stops.

Re

※

ference: if raising or lowering not completed within 6s, check the overload current

detecting function of door window motor or the installation of the door edging and door

window regulator.

（3）stepping mode power window

①

Operating condition: the same as that of power windows.

②

Within 0.3s, if power window switch is in its raising or lowering position, the

door window operates in stepping mode with the step length of 0.5s.

③

If raising and lowering switch is actuated in same direction N times within 0.3s,

the door window operates for a period of (0.5xN)s.

- 111 -