Chery S11 / Chery QQ. Manual — part 91
Chery QQ Service Manual
2. Remove front door sealing strips
Pull out sealing strips by hand
3. Remove outside inlaid strips
Take down screws and outside inlaid strips
4. Remove the upper inlaid strips
on windshield
As showed in the figure:Cut off
inlaid strips with knife
Attention:Do not let knife damage
car body
5. Remove windshield
(1)Lead piano wire out between car
body and windshield from interior car
(2)Bind up two wires ends with wood
blocks or similar objects
Note:Stick a piece of adhesive tape outside to prevent windshield external
surface from being scratched
Attention:
(1)Do not damage paint surface, internal
and external ornaments when detaching
piano wire
bonding agent
windshield
(2)To avoid the scratch on dashboard,
a sheet plastic can be placed between
piano string and dashboard
Drag the wire along all sides of windshield
to cut off bonding agent to remove windshield
Attention:Bonding agent should be kept on car body as much as possible
when cutting windshield joint
Chery QQ Service Manual
1. Installation of Windshield
(1)No touch on windshield surface
bonding agent
after cleaning
(2) Cut roughness off bonding agent sticking
to car body with knife
Note:Keep bonding agent on car body
as much as possible
(3)Clean the cutting surface of
bonding agent with a rag soaked in cleaning liquid
Note:Even though all of bonding agent is completely removed, car body surface must
be cleaned
stop
2. Remove block stop:
Remove block stop with knife
3. Clean the removed windshield
(1)Remove the bonding agent stuck
on windshield with scraper
(2)Clean windshield with cleaning
liquid
Attention:Do not touch windshield
after cleaning
4. Replace clamps if necessary
(1)Remove stops with knife
(2)Take down used clamps
(3)Put new clamps on
Chery QQ Service Manual
5. Position windshield
(1)Put windshield in right place
(2)Make reference marks on windshield
and car body
(3)Remove windshield
6. Clean the joint surface of windshield
Clean the black dirt with clean liquid on
the joint surface of windshield periphery
Attention:Do not touch windshield
surface after cleaning
7. Install water-resisting chips
As showed in the drawing,fix water-
7mm (0.28in)
resisting chips with double-side
adhesive tape
Attention:Do not touch windshield
surface after cleaning
8. Coat a layer of base paint M
bonding agent
base paint M
base paint M
base paint M
on the joint surface of car body
Brush a layer of base paint M
onto the joint surface of car body
Attention:
(1)Wait for base coating layer
to dry over 3 minutes
(2)No coating on bonding agent
(3)Never reserve unsealed base paint M
for later use
Chery QQ Service Manual
9. Coat a layer of base paint G on the
contact surface of windshield
base paint G
(1) Coat a layer of base paint G with brush
or sponge on windshield periphery and
joint surface
(2) Clear base paint with a clean rag
before drying
Attention:
(1)Leave base paint layer dry for 3 minutes at least
(2)No coating on bonding agent
(3)Never reserve unsealed base paint G for later use
10. Mix bonding agent
Attention:
A. Ensure the fixation of inlaid strip to
finish within the applicable duration
of bonding agent
B. Mixing bonding agent must be
completed within 5 minutes
(1) Clean glass plate and oil loam scraper
thoroughly with solvent
(2 ) Fully mix 500g principal agent with
75g hardening agent with scraper on
glass plate or similar object
11. Apply bonding agent
(1)Cut off the Note of tubular pot and fill
bonding agent in the pot
(2)Put the pot into sealing glue gun
(3)Apply bonding agent on windshield
as showed in the drawing
10mm (0.39in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст