Chery S11 / Chery QQ. Manual — part 216
SQR7080 Maintenance Manual 372 Engine Mechanical System
1 Make careful and detailed checks on the timing belt. Replace with new parts if any of the
conditions shown in the figure occurs.
(1)
、
Cracks on the back side rubber;
(2)
、
Cracks of teeth roots, cracks clearing off the fabric lining layer;
(3)
、
Tears and wears of fabric lining layer, missing rear teeth, broken teeth, etc.
(4)
、
Abnormal tears and wears on belt sides
Chap
Chap
Tears and
wears
Drop-off
of belt core
MIS
Abnormal
tears and
wears
7
SQR7080 Maintenance Manual 372 Engine Mechanical System
1 Even if the damages on the outer appearance can not be confirmed, the belt should be replaced
under any of the following circumstances:
(1)
、
If the water in the water pump is leaked, which makes it necessary to refill the water
continuously;
(2)
、
There are much oil stains on the belt, the belt should be replaced for the rubber will be
damaged when it is expanded;
Specifications and model of the timing belt
Model 372-1007081
Belt wide
25
.3mm
Timing belt tensioner
Turn the belt tensioner supporting stand bolts to see if there are any abnormal sounds. Check to see if
there are any damages on the contacting surface of the belt.
Specifications and model of the timing belt tensioner
Model 372-1007030
Wide
27.0
mm
Outside diameter
φ50mm
Check to see if there are any damages on the outer appearance
Specifications and model of clockwise pulley
EF
Model
Item
GL、ZL、GS、ZS
Diameter of camshaft timing
gear (mm)
φ110.7
+0.1
-0.2
Diameter of crankshaft timing
gear (mm)
φ54.65
+0.7
-0.13
2-3-4
Baffle of crankshaft timing gear
Check to see if there is any deformation
Standard size of crankshaft clockwisewheel:
Wide 28.6mm
8
SQR7080 Maintenance Manual 372 Engine Mechanical System
9
Installation
1 Installation of crankshaft timing gear
2 Installation of timing belt
(1)On the upper thrust point of the first cylinder
compression
①
Place the camshaft timing gear around the front
end of the air exhaust camshaft so as to make the
positioning groove on the gear be aligned with the
positioning pin on the end surface of the camshaft.
Then use screws to fix the clockwise gear, with the
torque of 100 ± 5N.m.
(2) Make sure that the punched mark on the
crankshaft clockwise pulley is aligned with the mark
of the oil pump.
(
3)Install timing pulley accordingly.
Timing mark
Timing mark
Timing mark
Clockwise
SQR7080 Maintenance Manual 372 Engine Mechanical System
10
3 Install the tensioner
(1)
Adjust the tension of the timing belt
As shown in the figure, make the space between the
①
edge of the stretching wheel and the water pump case
arc to be about 8mm;
Tig
②
hten the bolt of the stretching wheel with a
torque of 25 ± 3N.m. Use a screwdriver to swing the
stretcher toward the right..
③
Turn the crankshaft for two circles towards the
engine rotating direction, so that the camshaft pulley
and the crankshaft pulley matches the clockwise marks
respectively.
④
Use hands to press down for about 5mm. The force
for pressing the clockwise belt is about: [Referrence]
20~30 N
Notice: When the deflection of the timing belt fails to
meet the specifications, the key is to adjust the
above-mentioned stretcher fastening bolt by widening
the spacing.
Tighten the S/A fixing bolt of the stretcher with the
specified torque of 25 ± 3N.m
4 Install the baffle of the crankshafte timing pulley
[Attention] Install the baffle towars the direction
shown in the right figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст