Chery S11 / Chery QQ. Manual — part 208
Chery QQ Maintenance Manual 372 EFI System
DTC 18 IAT
进气压力温度传感器
Diagram of MAP and IAT
No. Operation
steps
Test
results
Next step
1
Turn on ignition key.
Next
Yes 4
2
Pull out the connectors on harness of
MAP and IAT and check if the voltage
between pin1 and pin 2 is 5V with
multimeter.
No Next
Yes
Repair or replace
harness
3
Connect the adaptor between ECU and
harness, check if open or short between
pin 48, pin 46, pin 60 of ECU and pin 1,
pin 3, pin 4 separately with multimeter.
No Next
4
Turn on ignition key but engine not run
Next
Yes Replace
ECU
5
Put on N shaft and run engine in idle. Step
down accelarate pedal to fully open.
Check if the voltage between pin 4 and
pin 1 of sensor is incrasing to 4V with
multimeter.
No
Replace ECU or
sensor
Chery QQ Maintenance Manual 372 EFI System
Oxygen sensor
主继电器
氧传感器
The diagram of oxygen sensor
No. Operation
steps Test
result
Next step
1
Turn on ignition key.
Next
Yes Next
2
Put out the connector on oxygen sensor and check
if the voltage between pin 1 and pin 2 is 12 V.
No 4
Yes Replace
ECU
3
Check if the resistance between pin 1 and pin 2 on
oxygen sensor is from 6 to 25.
No Replace
sensor
Yes Replace
fuse
4
Check if the fuse in oxygen sensor heating circuit
is burn out.
No Next
Yes
Repair or replace
harness
5
Check if open or short between pin 1 on sensor
and pin 87 on fuel pump relay, check open or short
between pin 2 and pin 59.
No Next
6
Insert the connector of oxygen sensor harness. Put
N shaft and run engine in idle to normal coolant
temperature.
Next
Yes Next
7
Put out the connectors of oxygen sensor from
harness. Check if output 0.1-0.9V voltage between
pin 4(+) and pin 3(-)
Yes Repalce
sensor
Yes
Repair or replace
harness
8
Connect the adaptor between ECU and harness.
Check if open or short between pin 43, pin 59 on
ECU and pin 3, pin 4 separately
No
更换
Replace
ECU
Oxygen sensor
Chery QQ Maintenance Manual 372 EFI System
DTC 18 IAT
进气压力温度传感器
The diagram of MAP and IAT
No. Operation
Steps
Test
result
Next step
1
Turn on ignition key.
Next
Yes Next
2
Put out the connectors on MAP and IAT
harness.Check if the voltage between pin 1
and pin 2 is 5 V.
No 4
Yes Replace ECU
3
Check if the resistance between pin 1 and
pin 2 is suit to the temperature ( see related
parts in this manual).
No Replace sensor
Yes
Repair or replace
harness
4
Connect the adaptor between ECU and
harness. Check if open or short between pin
30, pin 12, pin 44 on ECU and pin 1, pin 3,
pin 2 separately.
No Replace
ECU
Coolant temperature sensor
Chery QQ Maintenance Manual 372 EFI System
接仪表
b
The diagram of CTS
No. Operation
steps
Test
result
Next step
1
Turn on ignition key.
Next
Yes Next
2
Put out the connector on CTS harness,
check if the voltage between pin and pin c is
5V.
No 4
Yes Replace
ECU
3
Check if the resistance between pin a and
pin c is suit to the temperature ( see related
parts in this manual).
No Replace
sensor
Yes
Repair or replace
harness
4
Connect the adaptor between ECU and
harness. Check if open or short between pin
73, pin 31 on ECU and pin a, pin c
separately.
No Replace
ECU
Injector
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст