Chery S11 / Chery QQ. Manual — part 207
Chery QQ Maintenance Manual 372 EFI System
(6) Fault read out
The malfunction information records can be read out from ECU by tester, or be read by
flashing DTC codes. If the faults relate the function of fuel/air mix ratio regulator, engine will
read malfunction information records after running at least 5 minutes.
Fig. 3 ISO 9141-2 Standard diagnosis connector
The diagnosis connector install under glove box of sub cab
(7) Clear
DTC
When eliminate the faults, DTC should be cleared. There are 5 methods:
Clear DTC by using tester with the order of “clear DTC”.
Remove ECU terminals or battery terminals to clear DTC outside of RAM.
(8) Finding
faults
Getting above DTC means only to know the faults position, but not the real fault because the
reason for one fault may be the electric or mechanical one such as sensor, ECU or actuator
damage, or open circuit or short circuit or even mechanical damage.
Fault is internal, but the appearances are various. Firstly use tester or flashing light to check if
existing any DTC, and troubleshoot the faults accord to DTC, then find the reason of fault
according to engine symptom.
The step of fault diagnosis according to fault information record
DTC 13 A/C evaporator outlet temperature sensor
Chery QQ Maintenance Manual 372 EFI System
The diagram for A/C evaporator temperature sensor
No. Operation
steps
Test
results
Next step
1
Turn on ignition key.
Next
Yes Next
2
Pull out connector of A/C evaporator
temperature sensor, measure if the volt
between 2 pins is 5V with multimeter.
No 4
Yes Replace
sensor
3
Check any open or short between 2 pins
with multimeter.
No Replace
ECU
Yes
Repair or replace
harness
4
ECU and harness, check any open or short
between pin 30 , 39 of ECU and pin (1) and
(2) of sensor with multimeter.
No Replace
ECU
Chery QQ Maintenance Manual 372 EFI System
DTC 14 TPS
The diagram of TPS
No. Operation
steps
Test
results
Next step
1
Turn on ignition key.
Next
Yes Next
2
Pull out connector of A/C evaporator
temperature sensor, measure if the volt
between 2 pins is 5V with multimeter.
No
5
Yes Next
3
Measure the resistance between pin (1)
and (2) if in 1.6 to 2.4k with multimeter.
No Replace
sensor
Yes Replace
sensor
4
Run slowly TPS from one end to another
and check any open or short between pin
(1) and (3).
No Replace
ECU
Yes Repair
or
replace harness
5
Connect adaptor between ECU and
harness, check any open or short between
pin 12 , 30 of ECU and pin (1) and (2) of
sensor with multimeter.
No Replace
ECU
KS
Chery QQ Maintenance Manual 372 EFI System
爆震传感器
Diagram for KS
No. Operation
steps
Test
results
Next step
1
Turn off ignition key, engine nor run.
Next
Yes Next
2
Pull out connector of KS sensor, measure if
the resistance between pin 1, pin 2 of sensor
is over 1M with multimeter.
No Replace
sensor
Yes Next
3
Slightly knock around sensor with small
hammer and check if any AC signals putout
between pin1 and pin2 of sensor.
No
Replace sensor
4
Turn on ignition key but engine not run
Next
Yes
Repair or replace
harness
Connect adaptor between ECU anfd harness
and check any open or short between pin
11, pin 30, pin19 of ECU and pin 1 and pin2
and pin 3 with multimeter.
No
更换
ECU
Replace ECU
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст