Chery A series. Manual — part 114
10.Removal/installation of door switch
—
Disconnect the negative grid of the battery.
—
Loosen the self-tapping screw of the door switch with a cross screw driver.
—
Pull out the door switch, and separate the wiring harness connectors.
11.Removal/installation of control switch for dash lights
—
Disconnect the negative grid of the battery.
—
Reach the bottom part of the instrument panel with hand, and press down the clip of the
control switch for dash lights.
—
Pull the control switch for dash lights forward and remove it.
The installing steps of above components are reverse to those for removal
12. Beam adjustment for headlamp
—
The correctness of the beam adjustment for front headlamp is vital to the driving safety.
Therefore, only special instruments are allowed to be used to adjust the beam, and pay
attention to the stipulated laws during adjustment.
13. The followings must be fulfilled before adjustment
—
Air pressure of car tyres must comply with the standard;
—
The vehicle should be non-load (other than the spare tyre and tool kit, the weight of the car
normally includes the weight of the driver);
—
The car should be parked on a horizontal road or working site;
—
The surface of the headlamp reflector must be clean without any contamination;
—
Check whether power works normally and bulbs are installed properly.
—
Two screws linking the front headlamp can be adjusted towards the horizontal or vertical
position.
—
When adjusting the front right headlamp, the protection cover must be removed. The
adjustment screw for the front left headlamp is symmetrical with the front right one. The
adjustment method is the same.
T-14
COMMON MALFUNCTIONS OF LIGHTING SYSTEM / TROUBLESHOOTING
1.COMMON MALFUNCTIONS OF FRONT HEADLAMP / TROUBLESHOOTING
Malfunction Malfunction
Diagnosis
Troubleshooting
Neither high beam or low
beam light is working
1.All of bulbs have been damaged.
2.The fuse has been burned down.
3.Headlamp switch is faulty.
4.The circuit is faulty.
1.Replace the bulb.
2.Replace the fuse.
3.Inspect and replace the
headlamp switch.
4.Check the circuit.
Only one headlamp, that
is either the high beam or
low beam is working
1.The bulb has been damaged.
2.The fuse has been burned down.
3.The lamp holder or conducting
wire is faulty.
1.Replace the bulb.
2.Replace the fuse.
3.Check the lamp holder
or conducting wire.
Either side of the high
beam or low beam is not
working.
1.The bulb has been damaged.
2.The fuse has been burned down.
3.The headlamp switch is faulty.
4.The conducting wire or the
grounding is faulty.
1.Replace the bulb.
2.Replace the fuse.
3.Check the headlamp
switch.
4.Inspect the circuit.
Both headlamps are not
working.
1.The bulb has been damaged.
2.The fuse has been broken.
3.The headlamp switch is faulty.
4.The conducting wire or the
grounding is faulty.
1.Replace the bulb.
2.Replace the fuse.
3.Check the headlamp
switch.
4.Check the circuit.
Warning:
● The bulb will generate heat of very high temperature during working. So if the
surface of the bulb becomes dirty, the excessive heat will be accumulated, which
would result in shortening the life span of the bulb. When replacing the bulb, pay
attention to hold the metal edge rather than the bulb itself.
2. COMMON MALFUNCITONS OF FOG LAMP AND TROUBLESHOOTING
Malfunction symptom
Malfunction Diagnosis
Troubleshooting
Only one fog lamp is not
working
1. The bulb has been damaged.
2. The circuit or grounding is faulty.
1. Replace the bulb.
2. Check the circuit.
Neither of fog lamps is
not working
1. The bulb has been damaged.
2. The fuse has been burned down.
3. The fog lamp relay has been
damaged.
4. The fog lamp switch is faulty.
5. The circuit or grounding is faulty.
1. Replace the bulb.
2. Replace the fuse.
3. Check the relay.
4. Check the switch.
5. Check the circuit.
Fog lamp is always
working
1. The switch of fog lamp is faulty.
2. The circuit is faulty.
1. Check the switch.
2. Check the circuit.
T-15
Warning:
● The bulb will generate heat of very high temperature during working. So if the
surface of the bulb becomes dirty, the excessive heat will be accumulated, which
would result in shortening the life span of the bulb. When replacing the bulb, pay
attention to hold the metal edge rather than the bulb itself.
3. COMMON MALFUNCTIONS OF BACKUP LAMP AND TROUBLESHOOTING
Malfunction symptom
Malfunction Diagnosis
Troubleshooting
One side of the backup
lamp is not working
1. The bulb has been damaged.
2. The circuit or grounding is faulty.
1. Replace the bulb.
2. Check the circuit.
Neither sides of the
backup lamps is not
working
1. The bulb has been damaged.
2. The fuse has been burned down.
3. The backup lamp switch is faulty.
4. The circuit or grounding is faulty.
1. Replace the bulb.
2. Replace the fuse.
3. Check the switch.
4. Check the circuit.
Backup lamp is
continuously working
Incorrect adjustment or damage to the
switch of backup lamp.
Check the backup
lamp switch.
4. COMMON MALFUNCTIONS OF STOP LAMP AND TROUBLESHOOTING
Malfunction symptom
Malfunction Diagnosis
Troubleshooting
One side of the brake
lamps is not working
1 The bulb has been damaged.
2. The conducting wire or grounding is
faulty.
1. Replace the bulb.
2. Check the circuit.
Neither of the brake
lamps is not working
1. The bulb has been damaged.
2. The fuse has been burned down.
3. The brake lamp switch is faulty.
4. The conducting wire or grounding is
faulty.
1. Replace the bulb.
2. Replace the fuse.
3. Check the brake
lamp switch.
4. Check the circuit.
Brake lamp is
continuously working.
Incorrect adjustment or damage to the switch
of backup lamp.
Check the brake
lamp switch.
T-16
5. COMMON MALFUNCTIONS OF TURN SIGNAL LAMP AND
TROUBLESHOOTING
Malfunction
symptom
Malfunction Diagnosis
Troubleshooting
Left and right
flashing
frequencies are
not the same or
one side is not
flashing.
1. The bulb of the “fast flashing
frequency” side has been damaged.
2. The bulb power does not comply with
the specification.
3. The relay of turn signal lamp is faulty.
4. The conducting wire or grounding is
faulty.
1. Replace the bulb.
2. Replace the standard bulb.
3. Check and replace the
relay.
4. Check the circuit.
Both sides are not
flashing
1. The bulb has been damaged.
2. The fuse has been burned down.
3. The relay of turn signal lamp is faulty.
4. The switch of turn signal lamp is
faulty.
5. The conducting wire or grounding is
faulty.
1. Replace the bulb.
2. Replace the fuse.
3. Check the relay.
4. Check the switch of turn
signal lamp.
5. Check the circuit.
The flashing
frequency is too
low
1. Battery voltage is too low.
2. The bulb power does not comply with
specification.
3. The relay of turn signal lamp is faulty.
4. The circuit is faulty.
1. Check the battery and
recharge battery.
2. Change into the standard
bulb.
3. Check/replace the relay.
4. Check the circuit.
T-17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст