Chery A series. Manual — part 113

Technical parameters

Voltage value（V）

Current

value

（A）

11

Less than 90

LOAD INSPECTION OF STARTER

1. Verify that the battery is fully charged.

2. Initiate the engine, and check whether any block or noise during the rotation of the starter

rotor.

● If there is no abnormality, then please check the followings:

—

Remove the starter and check the solenoid switch and starter.

● Check the related winding coil and ignition switch.

T-10

LIGHTING SYSTEM

REMOVAL/INSTALLATION OF LIGHTINGS FOR THE COMPLETE CAR

1. Headlamp

Removal （Disconnect the negative grid of
the battery）

—

Remove the radiator grille, and use sleeve to
remove the four fixing bolts of the
headlamp.

—

Unplug the wiring harness connector behind
the headlamp holder.

—

Then place the headlamp on the

corresponding position.

Installation

—

Install the headlamp properly on the

corresponding position, and ensure that the
fixing hole position of the bolt is concentric
with the welded nut on the crossbeam of the
headlamp;

—

Use 4 bolts, spacers and 1 nut to locate the
position of the front headlamp, put down the
front hood, confirm and adjust position of
the headlamp (whether it is extruding or
intruding; the requirement is such that the
headlamp should be slightly extruded
beyond the front hood border. The arc shape
of the headlamp can be felt by hand), after
that tighten the fastener, with a tightening
torque of 1.5±0.2 N.m；

—

Install the radiator grille, and pay attention
not to scratch the paint on the protection
bumper; ensure that the spacing between the
left and right fenders is symmetrical.

—

Connect the wiring harness plug to the lamp
holder socket.

2. Removal/Installation of the front fog lamp: (Disconnect the negative grid of the
battery)

—

Connect the corresponding connector to the wiring harness of the fog lamp;

T-11

—

Place the fog lamp into the installation hole from the front, and ensure that the 3 screw
holes are concentric with the holes on the front bumper;

—

Tighten the 3 self-tapping screws, with a tightening torque of 1.5±0.2N.m;

—

Install the grilles on the bottom part (see instruction in car body)

3. Removal/installation of side turn signal lamp: (Disconnect the negative grid of the
battery)

—

Connect the wiring harness from the lamp holder;

—

First align the clipping end with car body in the correct direction, and then press it in by
force.

4. Removal/installation of fixed part of tail
lamps (including position lamp/brake lamp,
and turn signal lamp):

—

Align at the holes of car body, so as to install
the lamp on the body properly;

—

Tighten the 3 fixing screws, pay attention to
adjust the facial gap with the car body, feel
the difference in height with hand and make
necessary adjustment while tightening;

—

Plug the wiring harness onto the lamp

holder, and put back the carpet.

5. Removal/installation of moving part for
the tail lamp (including the backup lamp
and tail fog lamp)

—

Align at the holes of the car body, so as to
install the lamp on the body properly;

—

Tighten the 4 fixing screws, pay attention to
adjust the facial gap and spacing (the trunk
lid may be closed) with the car body and
fixing parts, feel the difference in height
with hand and make necessary adjustment
while tightening;

—

Plug the wiring harness onto the lamp

holder, and put down the trunk lid.

6. Removal/installation of license lamp

—

Connect the connector of the wiring harness properly;

—

Align the self-tapping screw with the hole center of expansion nut; tighten two self-tapping

screws with a tightening torque of 1.5±0.2N.m. Assemble the guard plate of license lamp;

T-12

—

Align lock core of the trunk with the hole, so as to match the guard plate with the car body
properly;

—

Tighten 2 self-tapping screw, pay attention to adjust the facial gap, spacing and other
differences between the car body and the movable part, feel the difference in height with
hand and make necessary adjustment while tightening;

—

Open the trunk lid;

—

Tighten 2 square nuts of the fixing bolt;

—

Assemble the linkage rod, lid, etc. of the lock hole (see instruction of car body), and then
put down the trunk lid.

7. Removal/installation of interior ceiling
lamp

—

Connect the connector of the wiring harness
properly；

—

Place it right into the installation hole of the
ceiling towards the correct direction, firstly
align one end with the ceiling and then press
the ceiling light into the proper position with
hand.

8. Removal/installation of trunk lamp

—

Open the trunk lid;

—

Connect the connector of the wiring harness properly;

—

Use the clipping end side to latch with cover of the back loudspeaker, after that just press
the light into it with hand. Put down the trunk lid;

9. Removal/installation of high mounted stop lamp

—

Press the two ends so as to separate the lamp holder and the lamp housing, and then pull out
the conducting wire connector;

—

Plug both of the single-terminal sockets of the conducting wires into the inserting plates of
the windscreen;

—

Install the lamp housing according to the combination structure of the clipping slot, pay
attention to the matching of the inverted slot with the fixing pin, so as to ensure that the
lamp housing is firmly clipped to the position;

—

Plug the conducting wire and lamp holder properly, and ensure that the lamp holder and

housing are assembled in the proper position.

T-13