Chery A series. Manual — part 137
Diameter of Main Journal And Size of Main Bearing Shell
Class
Diameter of main
journal (unit: mm)
Diameter of the main bearing
bore of the cylinder block
(unit: mm)
Thickness of the main
bearing shell (unit: mm)
Standard 57.98~58.00 62.2935+0.0065 2.131~2.138
Oversized by 0.4
57.98~58.00
62.6935+0.0065 2.331~2.338
Downsized by
0.02
57.98~58.00 62.2935+0.0065 2.141~2.148
Downsized by
0.25
57.73~57.75 62.2935+0.0065 2.256~2.263
Downsized by
0.50
57.48~57.50 62.2935+0.0065 2.381~2.388
Downsized by
0.75
57.23~57.25 62.2935+0.0065 2.506~2.513
Downsized by
0.25 and
oversized by 0.4
57.73~57.75 62.6935+0.0065 2.456~2.463
Downsized by
0.50 and
oversized by 0.4
57.48~57.50 62.6935+0.0065 2.518~2.558
Downsized by
0.75 and
oversized by 0.4
57.23~57.25 62.6935+0.0065 2.706~2.713
Size of Crankshaft Thrust, Thrust Spacer And Cylinder Block Thrust
Class
Size of cylinder block thrust
(unit: mm)
Size of crank shaft thrust (unit:
mm)
Thickness of thrust
spacer (unit: mm)
Standard 24+0.03 28.825-28.875
2.326+0.025
Oversized
by 0.38
24+0.03 29.205-29.255
2.516+0.025
TD-9
LUBRICATION SYSTEM
Lubricant Spec. (at above -10°C) SAE10W/30—50(SG grade)
Fuel Spec.
93 # Regular unleaded gasoline
Oil pressure (Idling Speed)
100Kpa
Oil pressure 2000r/min (water temperature 80℃) 280Kpa
Oil capacity (L)
3.86
Opening pressure of the pressure control valve, oil pump
(Kpa)
440±20
Opening pressure of the bypass valve, Oil Filter (Kpa)
78—118
Coolant Mixing Ratio
50% glycol +50% soft water (volume ratio)
Coolant Capacity (complete vehicle) (L) 8
Initial opening temperature of thermostat (℃) 85—89
Full open temperature of thermostat
99—102
Cap Pressure, expansion tank (Kpa)
160
Low-speed gear
High-speed motor 2000±200
Low-speed motor 1800±200
Fan speed
(r/min)
High-speed gear
High-speed motor2800±200
Low-speed motor2600±200
TD-10
COOLING SYSTEM
Cooling System
Parameters
Overall system capacity(L) 8
Engine capacity(L) 3.3
Radiator capacity(L) 2.1
Capacity of Coolant
Capacity of expansion tank(L) 0.4
Diameter: 280mm
Number of blades: 6
Working voltage: 9-15V
Rotating speed: Gear I: High-speed motor 2000±200
Low-speed motor 1800±200
Fan
Rotating speed: Gear II: High-speed motor 2800±200
Low-speed motor 2600±200
Diameter of impeller: ф72mm
Gear ratio: 1.053: 1
Water pump
Opening force of pressure cap: 160kPa
Front face area 0.202m²
Radiator
Radiation area 8.93m²
Opening temperature 85º-89º
Thermostat
Full open temperature 99º-102º
Switch-on temperature Gear I 95 Cº Gear II 102 Cº
Switch-off temperature Gear I≤84 Cº Gear II≤91 Cº
Thermal switch
Working voltage: 12V
CTS
ResistanceΩ: 70 Temperature Cº: 159±21.3
90 86.7±11
110 52.3±6.3
124 28.2±2.8
TD-11
ENGINE ELECTRICAL FUEL INJECTION SYSTEM
Marelli Electronic Fuel Injection System-New Camshaft+ New Standard:
Parameters
Normal value
Minimal value Maximal value
Engine Rotation Speed
(rpm)
880 (when air
conditioner is turned of)
850 910
Water Temperature (℃) >80
Throttle opening angle
(°)
Accelerator is released 0
0
0.6
Fuel injection duration (ms)
4.2ms (when air
conditioner is turned of)
3.4ms 4.7ms
In-take Pressure (mbar)
390mbar
340mbar
450mbar
Storage battery voltage
(V)
14 13
15
Oxygen sensor voltage
(mV)
Sinusoidal periodical
change
100mV 900mV
Steps of Stepping Motor
(step)
70 50
90
TD-12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст