Chery B11. Manual — part 111
Chery·Maintenance Manual for Oriental Son
Chassis Section
3、Check front-wheel bearing clearance, and replace front-wheel bearing if necessary.
4、Check if rims and tyres wobble.
5、Check if ball joint of cross connecting rod loosens.
6、Park the vehicle without luggage and persons on the level ground.
7、Heights from left and right sides of fender apron to vehicle center line can’t exceed standard height of checking
suspension.
8、Wobble wheels to check if shock absorber functions properly.
Note:*1 Make sure fuel tank is full of fuel, radiator coolant and engine oil are in the given height, the tyre jack and basic
hand tools are in the specified position.
II.
Rims and Tyres
1、
Sight Check
Check the rim and tyre, it is needed to replace
them, if crack and damage and deformation of
the rim and tyre are found .(see the figure)
Figure : Tyre Abrasion
2、
Tyre Abrasion
(1)
Check tread depth left. Standard
tyre illustrated in the figure: at least 1.6mm
Snow tyre: 50% of tread.
(
2)
It is needed to replace the tyre, if abrasion indicating
strip unfolds.
abrasion
indicating
point
Figure: Tyre Abrasion Indicating Point
abrasion indicating point
Chery·Maintenance Manual for Oriental Son
Chassis Section
3、Abnormal
Abrasion of Tyres
Undue abrasion of tyres illustrated in the
Double-side Wear
Center Wear
right figure may occur, consult possible
reasons and disposal methods in following
table. (See the figure)
Toe-in Wear
Figure: Tyre Abrasion
Single-side Wear
Possible reasons
Disposal methods
(
a)
*Lack of tyre pressure (abrasion on
both sides)
*Turn in high-speed
*Location of tyres hasn’t been adjusted.
* Measure and adjust tyre pressure
*Speed down
*Adjust tyre location
(
b)
* Tyre pressure is too high.
*Location of tyres hasn’t been adjusted.
*Measure and adjust tyre pressure
*Adjust tyre location
(
c)
* Incorrectness of toe-in
*Adjust toe-in
(
d)
*Incorrectness of camber or caster
* Suspension system failure.
*Tyre imbalance
*Out-of-round of brake drum or the
disk.
* Other mechanical problems
*Location of tyres hasn’t been adjusted.
*Adjust ,fix or replace the axle and
suspension system.
*Fix or replace
*Keep the tyre in dynamic balance or
replace it.
*Calibrate or replace
*Calibrate or replace
*Adjust tyre location
4、
Precautions related to rims and tyres
(
1)Don’t use substandard rims and tyres.
(
2)Aluminum alloy steel rim is likely to be scraped, so use soft fabric to clean it instead of steel brush. Don’t use
boiling water to clean it directly if cleaning vehicles with steam.
(
3)If
toothed compound
, such as mud or slurry is attached to aluminum alloy steel rim, it is needed to clean it with
neutral cleanser as quickly as possible to avoid damaging.
Chery·Maintenance Manual for Oriental Son
Chassis Section
5、Replacement of tyres
(
1)Before equipping inner tube valve, check if valve
hole is smooth without a bur. Then apply glycerol onto
the rubber surface of inner tube valve or dip inner tube
valve into glycerol.
It is finished with installation
correctly via passing binding ring of
inner tube
valve through the hole of the vehicle under the pressure
of 200-400N
with special tools (Suds is allowable
for replacement of
glycerol.
)
(
2)Before equipping tyres, apply glycerol or suds
onto the bead and note: when there’s a dub mark on
wheel rim, align the mark of tyre uniformity test with the
dub mark. When there isn’t a dub mark on wheel rim,
align the mark of dynamic balance test with inner tube
valve. When there is neither a dub mark on wheel rim nor
the mark of dynamic balance test, but there is a mark of
static balance test, align test mark of static balance with
inner tube valve.
6、Tyre pressure
Check pressure of all tyres, including spare tyres and adjust
it when needed. Inflate tyres according to given pressure
strictly. Air pressure can’t exceed 10% of rated air pressure
during inflation. When installing spare tyres assy separately,
rated inflation pressure shall be 3.5bar and they shall be
stocked in isolation from four wheels for equipping the
vehicle. Before processing four-wheel alignment, check
tyres pressure of 4 wheels and adjust it : front wheel :
2.2bar,rear wheel 2.0bar.(See the figure)
Check tyre pressure
tyre
Air Leakage
7、Air Leakage
Make sure there’s no air leakage of inner tube valve as
shown.
Chery·Maintenance Manual for Oriental Son
Chassis Section
8、Check out-of-flat of rims
(
1)Prop up vehicles high and safely.
(
2)Fix up micrometer indicator equipped with
cylindrical finger(Φ10)on the edge of wheel
Check out-of-flat of rims
rim to measure depth of out-of-flat.(see the figure)
(3)If needed, replace the
rim.
Note: allowable deformation in wheel rim:
allowable maximum value of out-of-flat depth average on both edges of wheel rims can’t exceed:
steel wheel rim:5mm ,
aluminum alloy wheel rim:3mm
9、Adjust tyre location
In view of extending tyre life and making sure tyre abrasion situation, adjust tyre location per 6000km
(
3750miles).
(See the figure)
Caution:
*It is needed to use the highest quality tyre for front wheel.
*After adjusting tyre location, adjust tyre pressure to assigned
pressure value.
Adjust tyre location
10、 Wheel balance adjustment
After tyre inflation, screw valve protecting cap
to process dynamic balance test and equip
suitable balance weight on the inner and outer
edges of wheel rim according to the requirement,
and require the last unbalance degree assy
is less than 100g· cm (about 5g of balance weight
on the inner and outer edges of wheel rim)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст