Chery B11. Manual — part 220
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
Second brake
hub oil seal
Strainer
Reference: the accumulator shall be aligned
ith the gearbox body.
7.
eal.
eference:
o. Components
connected
Wire
color
Plug
color
w
3 Fix the strainer and second brake hub oil
s
R
N
1 Underdrive
solenoid valve
White,
red, red
Black
2 Overdrive
solenoid
valve
Orange
, red
Black
3 Low/reverse-gear
solenoid valve
Brown,
yellow
Milky
4 Second-gear
solenoid valve
Green,
red, red
Milky
5 Damp
clutch
control solenoid
valve
Blue,
yellow,
yellow
Black
6 ATF
temperature Black,
Black
sensor
red
The fixing direction of oil seal is shown in the
gure.
8. Fix the seal washer and two steel balls of
e valve body.
eference: do not fix the valve body then.
9. Please tuck the wire harness of the
olenoid valve into the hole in the gearbox
over and then fix the snap ring.
fi
3
th
R
3
s
c
48
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
49
0. Fix 28 valve body bolts and screw them
ght with a tightening torque of 11Nm
.1Kg-m).
a screwing torque of 11Nm
4
ti
(1
41. Fix the ATF temperature sensor and
tighten it with
(1.1Kg-m).
油温传感器
Do not remove
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
42. Fix the manual control shaft brake and
crew the bolts tight with a tightening torque
f 6Nm (0.6Kg-m).
43. Please
body cover.
Liquid sealant:
Mitsubishi sealant Partl No. MD 974421 or
equivalent. Note: do not use sealant during
operation.
44. Fix the valve body cover and then screw it
tight with a torque of 9N
).
5. Fix the non-manual switch and screw it
6. Fix the manual control lever and screw it
ght with a torque of 22Nm (2.2Kg-m).
6. Fix input shaft speed sensor and output
s
o
50
apply the liquid sealant in the valve
m (0.9Kg-m
4
tight with a torque of 11Nm (1.1Kg-m).
4
ti
4
shaft speed sensor.
Manual
control shaft
Manual control lever
Non-
manual
switch
Input shaft
speed sensor
Output
shaft speed
sensor
Chery·Maintenance Manual for Oriental Son
Automatic Transmission
47. Fix the eyebolt, new seal washer and
ooler feeding pipe.
8. Fix the oil gauge.
9. Tighten the bracket with a torque of 23Nm
.3Kg-m).
0. Fix two brackets and tighten them with a
rque of 69Nm (6.9Kg-m).
1. Fix hydraulic torque converter and make
e dimension (A) in the figure comply with
e reference value.
eference value: about 12.2mm
ote: before fixing the hydraulic torque
onverter, apply ATF onto oil pump drive hub.
o not damage oil seal lips while fixing the
ydraulic torque converter.
Name
Use
c
4
4
(2
5
to
5
th
th
R
N
c
D
h
Stall Test and Oil Pressure Test
Special tools
Tool Serial
No
MB991502
Checking of
MUT-II
accessory
troubleshooting code
MD998332
Tie-in
Checking oil pressure
Checking oil pressure
MD998900
Tie-in
51
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст