Chery Tiggo T11 LHD. Manual — part 60
Chery T11 Service Manual Electric Injection System
53
Failure Code:
P0480-2
Open circuit of radiator low-speed fan relay drive circuit or
short circuit to earth
Set emergency control scheme:
Switch on the failure lamp till the failure disappears
NULL
Fan doesn’t operate (open circuit), till the water temperature
increases to 98℃ and then the high-speed fan activates
Fan operates normally (short circuit to earth)
Connection terminal:
MT 20U
Low-speed Fan Relay
Normal
Measurement Signal
Battery:
\
Refer to Electrical System
Description
12V
Relay drive:
67
Refer to Electrical System
Description
0V (Operating) and
12V (Stop)
Condition for Determination
Possible Reason
Actions
Failure duration > 3 s
1) Unreliable
connection
of
the
connecting parts
2) Short circuit of relay drive circuit to
the negative electrode of power
supply
3) Open circuit of relay drive circuit
4) Open circuit with the battery
connection circuit
5) Relay damaged
6) ECM failure
1) Connect again
2) Repair harness
3) Repair harness
4) Repair harness
5) Replace relay
6) Replace ECM
Failure Code:
P0481-1
Short circuit of radiator high-speed fan relay drive circuit to
the positive electrode of power supply
Set emergency control scheme:
Switch on the failure lamp till the failure disappears
NULL
Connection terminal:
MT 20U
High-speed Fan Relay
Normal Measurement
Signal
Battery:
\
Refer to Electrical System
Description
12V
Relay drive:
50
Refer to Electrical System
Description
0V (Operating) and
12V (Stop)
Condition for Determination
Possible Reason
Actions
Failure duration > 3 s
1) Short circuit of relay drive circuit
to the positive electrode of power
supply
2) Relay damaged
3) ECM failure
1) Repair harness
2) Replace relay
3) Replace ECM
Chery T11 Service Manual Electric Injection System
54
Failure Code:
P0481-2
Open circuit of radiator high-speed fan relay drive circuit or
short circuit to earth
Set emergency control scheme:
Switch on the failure lamp till the failure disappears
NULL
Fan operates normally (short circuit to earth)
Connection
terminal:
MT 20U
High-speed Fan Relay
Normal
Measurement Signal
Battery:
\
Refer to Electrical
System Description
12V
Relay drive:
50
Refer to Electrical
System Description
0V (Operating) and
12V (Stop)
Condition for Determination
Possible Reason
Actions
Failure duration > 3 s
1) Unreliable connection of the connecting
parts
2) Short circuit of relay drive circuit to the
negative electrode of power supply
3) Open circuit of relay drive circuit
4) Open circuit with the battery connection
circuit
5) Relay damaged
6) ECM failure
1) Connect again
2) Repair harness
3) Repair harness
4) Repair harness
5) Replace relay
6) Replace ECM
Chery T11 Service Manual Electric Injection System
55
T11 Vehicle Speed Sensor
Failure Code: P0500-0
No vehicle speed sensor signal
Set emergency control scheme: Switch on the failure lamp till the failure disappears
NULL
It is possible to take some driving limit measures
Connection terminal:
MT
20U
Vehicle Speed Sensor
Normal
Measurement Signal
Sensor signal earth:
03
/
0 to 12V square
wave
Condition for Determination
Possible Reason
Actions
Engine operation
Vehicle speed < 2 km/h
MAP < 25.82 kPa
1,200 rpm < engine speed < 5000 rpm
Throttle closed
Failure duration > 5 s
1) Unreliable connection of the
connecting parts
2) Interrupt of signal circuit from
the automatic transmission to
instruments
3) Interrupt of harnesses from
instruments to ECM
4) Vehicle speed sensor damaged
5) Instrument failure
6) ECM failure
1) Connect again
2) Replace flexible
shaft or signal
wire
3) Repair harness
4) Replace vehicle
speed sensor
5) Repair
or
replace
instrument
6) Replace ECM
Chery T11 Service Manual Electric Injection System
56
T11 Idle Stepper Motor
Failure Code:
P0505-0
Idle Control Error
Set emergency control scheme:
Switch on the failure lamp till the failure disappears
Pause the idle control
Connection terminal:
MT 20U
Idle Control Valve
Normal Measurement
Signal
Idle control valve A-high:
54
D
0 to 12V square wave
(with idle valve C)
Idle control valve A-low:
53
C
0 to 12V square wave
(with idle valve D)
Idle control valve B-high:
33
B
0 to 12V square wave
(with idle valve A)
Idle control valve A-low:
34
A
0 to 12V square wave
(with idle valve B)
Condition for Determination
Possible Reason
Actions
Engine idle operation
Water temperature reaches the normal
value
No TPS and VSS failure
Deviation from the target speed > 180
rpm
Failure duration > 15 s
1) Unreliable connection of the
connecting parts
2) Open circuit of any circuit of
idle valve
3) Error of corresponding relation
between
the
idle
valve
connecting parts and ECM
connecting parts
4) Intake manifold leakage
5) Idle control valve damaged
6) ECM failure
1) Connect again
2) Repair harness
3) Repair harness
4) Remove the leakage
failure
5) Replace idle control
valve
6) Replace ECM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст