Chery Tiggo T11 LHD. Manual — part 30
T11 Service Manual Chassis System
2.8.4 Battery Malfunction C1 101 and C1 102.
Within 9.4~17V or not?
Remove the connecting piece at harness side, then
turn the ignition switch to the position of ON, and
measure the voltage between pin4 (+), pin 8(-), pin4
(+) and pin 24(-).
Measure the voltage of +
and - of battery
Replace HECU
Inspect the mounting status of pin4, 8 and
24 of connecting piece at harness side as
well as the pin displacement.
Is the status all right?
Measure the resistance between
pin4 (+) of the connecting piece
at harness side and battery (+).
Inspect and replace battery
①No
Yes
Yes
No
No
Yes
Adjust
connecting
piece
pin
and
correctly mount the
connecting piece.
Is the status all right?
Confirm and inspect the
grounding condition of pin8
(-)
and
pin24
(-)
of
connecting piece at harness
side.
Start the engine, and measure the
voltage between pin4 (+), 8(-),
4(+) and 24(-).
Recheck
from
item
①
Yes
Yes
It is less than 9.4V?
No
It is less than
1Ω?
Is it more than 17V?
Replace AC generator
Yes
Adjust and ensure
the installation is all
right
In
sp
ec
t
an
d
re
p
lac
e
wirin
g
No
T11 Service Manual Chassis System
2.8.5 Solenoid Valve Fuse or Solenoid Valve Relay Malfunction C2 112.
No
It is electrified or not?
After removing the connecting
pieces at harness side, confirm if
the pin25 at the harness side is
electrified to ground wire or not.
Confirm if it is electrified
between
the
pin25
at
harness
side
and
the
terminals inside fuse box.
Inspect and replace the wiring of
pin25 at harness side.
Replace fuse
Inspect the fuse (30A) inside
fuse box
The fuse is normal or not?
No
Yes
Yes
No
No
Yes
Is the status all
right?
Replace HECU
Inspect the mounting status of
pin25 of connecting piece at
harness side and its offsetting
condition.
Adjust
connecting
piece pin and correctly
mount the connecting
piece.
Recheck from item
①
Yes
No
It is electrified or not?
Inspect
and
replace the wiring
of
pin25
at
harness side.
Yes
Use analyzer to drive
HECU by force
Is it all right?
T11 Service Manual Chassis System
2.8.6 Motor Fuse or Motor Malfunction C2 402.
①
It is electrified or not?
After removing the connecting
pieces at harness side, confirm if
it is electrified between pin9 at
harness side and ground wire or
not.
Confirm if the pin9 at
harness side is electrified
with fuse terminal inside
the box or not.
Inspect and replace the wiring of
pin9 at harness side.
Replace fuse
Confirm if the motor fuse is
burnt out or not.
The fuse is normal or not?
No
Yes
Yes
No
No
Yes
Is the status all
right?
Replace HECU
Inspect the mounting status of pin9
of connecting piece at harness side
and its offsetting condition.
Adjust
connecting
piece pin and correctly
mount the connecting
piece.
Recheck from item
①
Yes
No
It is electrified or not?
Inspect
and
replace the wiring
of pin9 at harness
side.
Yes
Use analyzer to drive
HECU by force
Is it all right?
No
T11 Service Manual Chassis System
2.8.7 ECU Internal Circuit or Valve Coil Malfunction C1 604
No
Remove the connecting piece of
harness, and measure the resistance
between the No.8 and 24 pin and
ground wire.
It is less than 1Ω or not?
Confirm
and
inspect
the
grounding status of No. 8 and
No. 24 pin.
Replace HECU
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст