Chery Tiggo T11 LHD. Manual — part 83

(5) Daub paint mark on every nut head.

(6) Daub paint mark on the main

bearing cap of which the position is

from paint mark on bolts to

screwing direction of 90～100°

(7) Screw nuts on from 90 ～ 100 °

regulated in the picture above,

according to screwing order till paint

mark on bolts aligns paint mark on

main bearing cap.

Notice:



If screwing angle is less than 90°,

screwing specified capability can’t

be assured. When screwing it on,

pay much attention to screwing

angle.



If screwing nuts are excessively

tightened (exceed angle of 100°) ,

screw nuts off totally. And restart

to screw nuts from Step 1.

(8) After installing main bearing cap,

assure if crankshaft can turn

smoothly and check axial clearance.

If axial clearance exceeds usage

limit value, replace NO.3 crankshaft

thrust bearing of crankshaft.

Standard value：0.05～0.18mm

Limit value：0.25mm

Oil seal installation

Rear oil seal cap installation
Specified sealant：
Brand ： Mitsubishi pure components
MD970389

or

corresponding

equivalents.

Notices:

(1) Ensure rear oil seal cap is installed

quickly when sealant is still wet.

( ≤15 min)

(2) After installing, keep sealed

area away from lubricate grease

and coolant for one hour.

Arrow

Paint mark

Paint mark

Service Manual for Chery·Tiggo(T11) Engine Section

Chapter 5 Lubrication System

Front cover, oil pump, balance axle and

oil pan

Disassembling Steps
1.Oil cleaner
2.Oil drain plug
3.Oil drain plug cushion
4.Oil pan
5. Oil collect filter
6. Oil collect filter cushion
7. Plug
8. O-shape ring
9. Flange bolt
10. Oil pressure switch
11. Pressure relief plug
12. Seal cushion
13. Pressure relief spring
14. Pressure-relief plunger

15. Oil cleaner bracket
16. Oil cleaner bracket cushion
17. Oil pump cover
18. Oil pump driven gear
19. Oil pump drive gear
20. Crankshaft front oil seal
21. Oil pump oil seal
22. Balance axle oil seal
23. Front cover
24. Front cover cushion
25. Left balance axle
26. Right balance axle
27. Right balance axle front bearing
28. Left balance axle bearing
29. Right balance axle rear bearing

Daub oil on all internal

components

when

assembling

Disassembling
illustration

Service Manual for Chery·Tiggo(T11) Engine Section

Disassemble Notice

Oil pan disassemble

(1) Disassemble all oil pan bolts

(2) Insert special tool between cylinder body and

oil pan.

Remarks：

Do not use screwdriver or chisel instead of

special tool, otherwise the edge of oil pan

may be distorted and oil leakage will occur.

Plug disassemble

Disassemble plug cock with special tool. If

plug is tightened, tap the plug top with

hammer several times and the plug will loose.

Flange bolt disassemble

(1) Disassemble plug from cylinder body.

(2) Insert cross screwdriver (pole diameter is

8mm) into the plug hole and lock balance

axle.

(3) Loosen flange bolt

Right balance axle front bearing disassemble

(1)Disassemble balance axle right-front bearing

with special tool from cylinder body.

Remarks：

Front bearing must be disassembled firstly. If it is

not disassembled, rear bearing puller can not be

used.

MD998727

MD998162

plug

Screwdriver

MD998371

Front

bearing

Maintenance Manual for Chery·Oriental Son

Engine Section

Balance axle rear bearing disassemble

Disassemble left balance axle rear bearing

with special tool from cylinder body.

Remarks：

Special tool (MB991603) should be installed

in front of cylinder body when disassembling

left balance axle rear bearing.

Installation Notice

Right balance axle rear bearing installation

(1) Daub oil on bearing surface.

(2) Install right rear bearing with special tool.

Make sure that oil holes on bearing and

cylinder body are aligned.

Left balance axle rear bearing installation

(1) Install special tool (conducting board) on

cylinder body.

(2) Daub oil on rear bearing edges and inside

cylinder body bearing holes.

(3) Install rear bearing with special tool

Remarks：

There is no oil hole in left rear bearing.

MB991603

MB998372

MD998705

MB991603

MD998705

MB991603

MD998705

Rear

bearing