Chery Tiggo T11 LHD. Manual — part 131

Chery International Maintenance and Service

be between the marks of MIN and MAX.
When the engine is hot, the fluid level
may exceed the MAX due to heat
expansion.

ONLY add coolant when engine is cool.
If you have to add it while the engine is
hot, wait for 10 minutes till the engine is
cool. Firstly unscrew the cap for ¼
circles to relieve the accumulated
pressure. Then open it after a period of
time. Finally add the mixture of 50%
water and 50% coolant.

Warning: Avoid coolant
splashing on any parts

of vehicle when add the fluid.

Engine Coolant

Prevent the fluid from
contact with skin or eye.

If it happens, wash it with
enough water and consult a
doctor immediately.

Coolant with proper concentration
cannot only prevent engine from
freezing, but also provide corrosion
protection. Modern engine operates
with high temperature. Therefore,
inferior coolant cannot protect engine
from corrosion.

Always use coolant conforms to Chery
specification. Please refer to “Capacity
and Specification” for details.

Please do not use
coolants mixed

with

different

colors

and

specifications.

Add coolant when engine is
cooled down

Chery International Maintenance and Service

Check the Power Steering
Fluid Level

When the engine is cold, the level shall
reach the mark of MAX. If the level is
below the mark of MIN., please add
specified fluid.

Battery

Battery does not require much
maintenance, so its liquid level will be
checked in regular maintenance.

The onboard battery is completely
maintenance free. Please do not use
battery of other types. The current and
capacity of new battery shall agree with
the used one or conform to Chery
specification. Please contact Chery
Authorized Service Station for proper
specification.

Windscreen Washer system

The front and rear washers are watered
by the same reservoir. If necessary, mix
the water and windscreen shampoo in
1:20.

Refer to the instruction on the reservoir
for proper concentration.

Please screw the cap home after

mixing.

Chery International Maintenance and Service

Check

for

Windscreen

Wiper Blade

Slide your fingertip on the edge of the
blade to check its coarseness. Grease,
silicone and fuel might

cause

malfunction of the blade. It is
recommended to clean the blade with
glass shampoo.

Wiper Blade Replacement

Raise the wiper arm till it becomes a
right angle to the blade. Press the
spring retainer following the arrow, and
then oppositely pull the blade out of the
wiper arm to extract the blade.

Tire

To ensure your safety, please refuel
only after the tire is cooled down.

Please check the tire pressure ONLY
after the tire is cooled down (including

spare wheels). And refer to “Capacity
and Specification” for recommended
pressure value.

Comply with correct tire pressure when
driving at high-load and high-speed.
Insufficient pressure may result in less
reliability, larger rolling resistance and
grave tire abrasion, and consequently
traffic accident will occur.

If you have to drive onto the road edge,
maintain low speed and keep the wheel
in right angle to approach the roadside
if possible. Avoid upstanding and sharp
obstacles. And brake carefully to avoid
the tire side being scratched.

Regularly check the tire surface for
scratch, foreign objects and uneven
abrasion. Uneven abrasion indicates
the wheels are not being properly

Chery International Maintenance and Service

positioned.

Regulations specify the depth of the
abrasion on the tire surface. When the
depth reaches the limit of 3mm, an
abrasion zone will appear on the tire,
which indicates the tire must be
replaced due to tire reliability and
security is greatly reduced.

Dispose the

worn

tire

according

to

local

environmental protection regulations.
Change the winter tire to summer tire
as soon as road condition permits,
which can reduce fuel consumption and

lower the noise.

Wheel Replacement

Improper tire and wheel
may result in accident,

and not covered by the warranty.

Your wheel is carefully chosen to
ensure optimum operation, comfort and
security. The above specifications for
tire and wheel are also applicable for
steel or aluminum-alloy wheel. Please
contact Chery Authorized Service
Station for other applicable tire and
wheel.

It is recommended to use original tire or
refer to Chery recommendations.

If you intend to install
untypical tire or wheel

(e.g., light-alloy wheel or winter

tire), please comply with relating
instructions or contact Chery
Authorized Service Station.

Notice:

The speedometer is affected by wheel
dimension. If the diameter of the wheel
is different with the original one, please
send your vehicle to Chery Authorized
Service Station

to

adjust the

speedometer. Otherwise, you cannot
get the correct speed indication from
the speedometer.

Snow Chain

Snow chain can be applied to all of the
summer and winter tires listed in the
table, but only applicable to the driving
wheel (front wheel).