Chery Tiggo T11 LHD. Manual — part 35
T11 Service Manual Suspension and Steering
Section 1 Specification
Fastener Tightening Specifications
Part number Specification Torque
(N.m)
Quantity
Affixed assembly
Q330C10
M10×1.25
40~50 2
Connecting rod and front stabilizer bar
Q330C10
M10×1.25
40~50 2
Front connecting rod and front shock absorber
Q1420825
M8×25
22~28 4
Fix stabilizer bar clip to subframe
T11-2901011
M10×19
45~55 6
Front suspension strut and vehicle body
T11-2901013
M15×1.5
110~130 4
Steering knuckle and suspension strut
T11-2901015
M15×1.5×55 110~130 4
Steering knuckle and suspension strut
Q330C10
M10×1.25
40~50 2
Connecting rod and rear stabilizer bar
Q330C10
M10×1.25
40~50 2
Connecting rod with lower suspension lever
T11-2919037
(Q184B1280)
M12×1.25×8
2/80
100~120 2
One on each side to connect upper link with
towing arm
Q330B12
M12×1.25
80~101 2
One on each side to connect upper link with
towing arm
Q1401282
(Q184B1280)
M12×82
100~120 2
One on each side to connect upper link with
rear subframe
Q330B12
M12×1.25
80~101 2
One on each side to connect upper link with
rear subframe
Q1401282
(Q184B1280)
M12×82
100~120
2
One on each side to connect lower control arm
with towing arm
T11—2919035
(Q184B12100)
M12×94×1.2
5/95
100~120
2
One on each side to connect lower control arm
with rear subframe
T11—2919031 M12
100~120 2
One on each side, fit onto the T11-2919035.
Q334C10
M10×1.25
22~28 4
Two on each side to connect the upper end of
rear shock absorber with vehicle body
T11—2915013 M10×19
40~50 2
Connect rear shock absorber with rear shock
absorber mounting bracket (T11-3301110)
Q1400820
M8×20
22~28 1
Fix the rear rubber buffer assembly onto the
vehicle body
T11-3100111
100~120 23
Wheel nut
Q184C1090
Dacroment
Grade 10.9
75~85 1
Soft gasket and bracket of front suspension
Q330C10
Galvanization
Grade 10
75~85 1
Front suspension and bracket
Q184B1285
Dacroment
Grade 10.9
110~130 1
Soft gasket and bracket of rear suspension
Q330B12
Galvanization
grade 10
115~125 1
Rear suspension and bracket
Q184C1260
Dacroment
Grade 10.9
75~85 2
Connect the rear axle front suspension with rear
driving axle
T11 Service Manual Suspension and Steering
Q330B12
Dacroment
Grade 10.9
115~125 2
Connect rear axle front suspension with rear
subframe, there are bolts on the suspension
Q140B1230
Dacroment
Grade 10.9
75~85 1
Rear suspension, longitudinal beam of engine
and subframe
Q330B12
Nut
110~130
2
Insert from the lower part of subframe, and the
bolt is on the suspension. The middle part
shall be clamped to the main longitudinal beam
of engine.
T11 2402013
Dacroment
Grade 10.9
75~85 2
Fix the rear axle rear suspension cushion
assembly onto the rear axle
T11 2402011
Dacroment
Grade 10.9
75~85 2
Fix the rear axle rear suspension cushion
assembly onto vehicle body
T11 2203205
Grade 8
260~280 2
Connect the right and left assembly of front
drive shaft with brake disc
T11 2201205
Grade 8
260~270 2
Connect the right and left assembly of rear
drive shaft with brake disc
Q32608
20~26 12
Connect the right and left assembly of rear
drive shaft with rear axle
T11 2202201
Grade 8.8
58~68 2
Connect intermediate propeller shaft with
vehicle body
0142B1030
Grade10.9
75~85 4
Connect intermediate propeller shaft with rear
axle
Q330B10
Grade 10
75~85 4
Connect intermediate propeller shaft with rear
axle
N0111862
M12×12
35~45 2
Steering knuckle tie rod and steering knuckle
AQl40C1035
M10×1.25(wi
th guide)
74~86 2
Longitudinal beam and flat gasket of vehicle
(front) body
T11 2810011
M14×1.5(55) 170~190 2
Subframe and gasket of vehicle (rear) body
T11 2810013
M14×1.5
(118)
170~190 2
Subframe and gasket of vehicle (front) body
Q14081230/40 Bolt
75~85 2
Subframe and longitudinal beam welding
assembly
Q330C10
Nut
75~85 1
Subframe and longitudinal beam welding
assembly
01420820
M8×20×1.25
22~28 4
Rear stabilizer bar clip and vehicle body
T11-2919035
Grade 10.9
140~160 2
Rear towing arm and vehicle body
AQl84B1220
M12×1.25
×20
140~160 2
Connect control arm knuckle pin with control
arm
T11-2909063
M12×1.25
140~160 4
Connect control arm knuckle pin with control
arm
T11-2909061
M12×1.25
140~160 4
Connect control arm knuckle pin with control
arm
AQ330B14
M14×1.5
170~190 2
Control arm and subframe
Q184B1275
M12×60
75~85 2
Steering gear and subframe
T11 Service Manual Suspension and Steering
T11-2909011
M14×1.5
110~130 2
Connect control arm knuckle pin with knuckle
assembly
T11-2909013
M14×1.5
170~190 4
Control arm and subframe
AQ330B14
M14×1.5
170~190 2
Rear gum cover of control arm and subframe
Once loosening the binding bolt whose torque and angle tightening condition is controlled by
yield limit in screw fastening, it must be replaced.
1) Pretension to 100N.m, then loosen capstan nut and tighten to 120N.m, finally rotate 90°. If the
cotter pinhole cannot be aligned with capstan nut, loosen it and return to the next hole. Then fix it
by cotter pin.
2) Pretension to 50N.m, and then tighten to 90Nm, finally rotate 45
0
to 60
0
.
3) Tighten to 90N.m and then rotate 30
0
to 45
0
.
4) Tighten to 50N.m and then rotate 90
0
to 105
0
.
T11 Service Manual Suspension and Steering
Section 2 Removal and Installation of Front Shock Absorber
The front axle of Chery SQR7246/7247/7206 automobile employs on-off type steering driving
axle, and the suspension is McPherson independent suspension. The front suspension of
SQR7246/7247/7206 automobile performs dual functions such as driving and steering. The
upper end of the suspension is connected to vehicle body, whereas the lower end is joined to
steering knuckle. The camber angle is adjusted via the connecting bolt that joins suspension and
steering knuckle.
Ⅰ Exterior Identification
1. Disassembly drawing:
——Place lower rubber pad 68 on the tray of front shock absorber 52. Fit front buffer block 64
and front dust cover 62 over the piston rod of front shock absorber. And then fit coil spring 66.
Compress the front coil spring to less than 275mm, then mount front spring upper tray 60, bearing
gasket 58 and attachment bracket assembly 56 (including bearing) in sequence, finally torque nut
54 to specification and loosen the compressor of coil spring.
——When assembling, the two terminals of front coil spring shall contact with the corresponding
set locations on the spring tray.
——Pay close attention to the mounting angle of front spring upper tray to prevent bearing from
damage due to wrong fixing.
2. Removal and installation of front shock absorber
Disassembly procedure:
1) Jack the vehicle and then remove front wheels.
Coil Spring
Left
Front
Shock
Absorber Assembly
Lower Rubber Pad
Upper
Cover
of
Front
Suspension Struts
Connecting Bracket Assembly
Bearing Gasket
Spring Upper Tray
Dust Sleeve
Front Buffer Block
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст