Chery Tiggo T11 LHD. Manual — part 36
T11 Service Manual Suspension and Steering
2) Remove hose, vehicle speed sensor cable of ABS (if available), hose bracket and brake cable
clip from shock absorber.
3) Remove the steering knuckle with brake disc assembly from shock absorber.
a) Unscrew two nuts and bolts that join the
shock absorber and the steering knuckle with
brake disc assembly.
b) Unscrew the bolt that connects steering
knuckle tie rod knuckle pin and steering
knuckle with brake disc assembly, and then
loosen the knuckle pin.
c) Unscrew the bolt that connects the front
connecting rod to the shock absorber, and then
loosen the front connecting rod.
T11 Service Manual Suspension and Steering
d) Unscrew the bolt that connects the steering
knuckle with brake disc assembly to control
arm knuckle pin.
e) Unscrew the driving bolt from the front
wheel.
f) Remove the steering knuckle with brake disc
assembly from shock absorber.
Installation tips: apply engine oil to nut thread.
4) Remove both shock absorber and coil spring.
a) Remove the three nuts joining the shock absorber to vehicle body.
b) Remove the shock absorber together with coil spring.
Installation procedures:
1) Refer to disassembly procedures to perform assembly.
2) Precautions:
a) Once loosening the binding bolt whose torque and angle tightening condition is controlled by
yield limit, it must be replaced.
b) After installation, torque each bolt to specification.
c) Check the wheel alignment after installation
3. Inspection
1) Inspect shock absorber.
T11 Service Manual Suspension and Steering
a) Inspect shock absorber for oil leakage, and
replace if necessary. Then inspect the damping
force of shock absorber, and replace it if not
conform to the specification.
b) Inspect the thrust bearing for excessive wear
or abnormal noise of block. Then inspect the
lower spring seat for cracks or deformations.
Subsequently inspect the limit stop for
damages. Finally inspect the stop pad for wear,
crack or deformation. And replace defective
parts.
Note: Refer to the following procedures when discarding shock absorber.
2) Disposal of front shock absorber
a) Stretch the shock absorber rod as far as
possible.
b) Discharge the gas inside the shock absorber
cylinder by bit to drill a hole in the cylinder
body (as shown in the figure).
Caution: The gas discharged is hazardous-free,
however, and be cautious to scrap iron splashes
when drilling the cylinder body.
4. Removal and installation of shock absorber bracket, shock
absorber bracket components and/or spring
Removal and installation of spring
1) If the assembly fixture cannot be fixed onto
the workbench, fix it into bench vice.
T11 Service Manual Suspension and Steering
2) Fix a pair of claws that match the spring
diameter into the spring compressor.
Disassembly procedures
1) Loosen the spring compressor, then locate the
claws between the top and bottom of springs
(As shown by the arrow).
2) Compress the spring till the spring is released
from spring seat.
3) Remove the shock absorber support bracket
with limiter and washer from connecting rod via
ratchet wrench (as shown in the figure) that is
used to unscrew lock nut.
4) Remove the upper spring seat with absorber
block.
5) Remove the spring compressor with spring
and dust cover.
6) Remove buffer block.
7) Inspect the disassembled parts according to
damage and wear condition.
a) Buffer block.
b) Dust cover.
c) Vibration isolator.
d) Shock absorber support bracket.
e) The upper spring seat with bearing and
limiter.
8) If the used shock absorber needs to be replaced, firstly remove wheel speed sensor harness
bracket from the shock absorber, then fix it onto a new shock absorber (if there is no wheel sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст