Chery Tiggo T11 LHD. Manual — part 125

Chery International Driving

Back light bulb

1.

Open the tail door. From the
interior of luggage boot, release
the revolution clip of back light
assembly cap. Pull out the light
assembly slightly.

2.

Screw off the lamp receptacle
according to the inverse direction
of the locking direction indicated
on the lamp receptacle, and then

draw out the bulb socket.

3.

Use the slight pressure to press
and

turn

the

bulb

counterclockwise, and then draw
out the bulb. Replace the bulb.

4.

Install a bulb according to the
reverse sequence.

5.

Check the light/lamp is work
normally after the completion of
installation.

Brake light bulb

1.

Open the tail door. Remove two
crosshead screws and the cover
plate. Disconnect the cable joint
and take out the light assembly.
Pull out the cover plate. And
draw out the bulb and replace it.

2.

Install it according to the reverse
sequence.

License light bulb

The installation site: the light is
installed under the protective plate of
license light.

1.

Remove the tapping screws used
to fix the license light, and take
off the license light.

2.

Pull out the lamp receptacle, and
draw out the disable bulb.

3.

Install a new into the lamp
receptacle, and then install the
receptacle.

4.

Use the tapping screws to fix the
license light.

Rear position

light

Brake light

Backup light

Rear directional

signal light

Chery International Driving

Interior front/rear ceiling
light bulb

1.

Switch off the interior lights.

2.

Insert the screwdriver into the
space between the lamp housing
and the lamp shade, and pry out
the lamp shade carefully.

3.

Replace the bulb, and install the
reflector.

4.

Install the lamp shade into the
mounting hole of the lamp
housing again.

Sun visor’s dressing
mirror light:

The light is situated in the back of sun
visor.

Pry out the glass block. And replace
the bulb.

Luggage boot light bulb

The installation site: the light is
installed on the faceshield of left back
loudspeaker.

1.

Squeeze the A position by hand
from the back of the light, get
across the convex step of the
light fitting and then remove the
luggage boot light.

2.

Replace the bulb.

3.

Install the new bulb into the
mounting hole on the faceshield
of loudspeaker.

Adjust the headlamp beam

The right adjustment of headlamp
beam is directly referred to the driving
security. Thus, the special instruments
are allowable only to adjust the beam.
Please attention to the laws and
regulations when adjusting.

The position of headlamp shall be
suitable for the load state of the
vehicle.

4.

The adjusting screws for the

Adjusting
screw

Chery International Driving

headlamp are shown in the figure
above. The adjusting screws of
left/right headlamp are arranged
symmetrically, which their
adjustment methods are the
same as each other.

Fuse and relay

The ignition switch and
all electrical equipment

shall be turned off before the
fuse and relay are replaced.

Replace the disable fuse with a new
fuse with the same rated value. The
position of the fuse box including the
main fuse and relay is shown in the
figure below.

Replacing the relay requires the
related professional knowledge.

It is recommended that multiple spare
fuses shall be carried with your vehicle
for emergency use.

The Chery Authorized Service Station
has various kinds of fuses.

The brownout fuse can be identified in
term of the fuse broken. All fuses are
the push-type.

Small fuse

Cartridge fuse

Any

unauthorized

change on the vehicle

electrical or fuel system can be
able to make influence on the
performance of vehicle and may
result a fire disaster or hazard on
security. So, it is recommended
that any work related to removal
of fuel or electrical system or
replacement of relay is
implemented by the Chery

Chery International Driving

Authorized Service Station.