Chery QQ6 (S21) / S12LHD. Manual — part 123
Page 17 of 38
of which the operation method is same with that of the trouble code diagnosis.
In addition, when the ECU of the ABS has no trouble code, ground the line L and rotate the
key to the power on position. The flashing of the ABS warning lamp is conducted in
accordance with the type in following figure, of which the symbol meaning is same with the
foregoing section.
2.4 Trouble Checklist of Trouble Code
①
Contents of Trouble Code
Trouble
code
Contents
Trouble
code
Contents
C1 200
(11)
Open-circuit/short-circuit of left
front sensor
C1 206
(31)
Open-circuit/short-circuit of left rear
sensor
C1 201
(12)
Interference of left front sensor or
gear ring
C1 207
(32)
Interference of left rear sensor or gear
ring
C1 202
(13)
Air gap error of left front sensor
C1 208
(33)
Air gap error of left rear sensor
C1 203
(21)
Open-circuit/short-circuit of right
front sensor
C1 209
(41)
Open-circuit/short-circuit of right rear
sensor
C1 204
(22)
Interference of right front sensor
or gear ring
C1 210
(42)
Interference of right rear sensor or
gear ring
C1 205
(23)
Air gap error of right front sensor
C1 211
(43)
Air gap error of right rear sensor
C1 101
(51)
Battery voltage too high (above
17V)
C2 112
(54)
Trouble of electromagnetic valve fuse
or electromagnetic relay
C1 102
(52)
Battery voltage too low (below
9.4V)
C2 402
(55)
Trouble of motor fuse or motor
C1 604
(53)
Trouble of ECU internal circuit or
electromagnetic valve coil
Line L
Ignition
Switch
ABS warning
lamp
Page 18 of 38
②
Trouble checklist of trouble code
Table 1
Trouble Code
C1 200(11)
C1 203(21)
C1 206(31)
C1 209(41)
Possible Case
Open-circuit/short-circuit of sensor:
At short-circuit or open-circuit
of batter y anode or cathode of
sensor.
Note: If the malfunctions corresponding to
more than 2 trouble codes can be determined,
after the trouble codes are deleted (erasable
trouble codes), drive the vehicle to above
40km/h to determine the malfunctions to that
the trouble codes correspond and check in
accordance with the registered trouble codes
(determine the same one trouble code).
Troubleshooting
Flow
No
No
Yes
Yes
Yes
Harness
Sensor
Sensor Head
Is status good?
Remove the connector from the
harness and sensor, confirm the
assembling status, and check the
pins for deviation
Correct the connector
pins
and
correctly
assemble the connector
Is powered on?
Replace sensor
Replace HECU
Is the problem
still present?
Determine and repair
wiring broken portion or
replace wiring
Determine if the two lines between
harness side pin A and connector B
of sensor assembly are powered
Page 19 of 38
Table 2
Trouble Code
C1 202(13) C1 205(23)
C1 208(33) C1 211(43)
Possible Case
Air gap error:
Air gap too big or self short-circuit
of sensor (resistance value at 0) that
results no signal or the gear ring
not properly installed.
Note: ①The air gap refers to the gap between
the gear ring and the sensor;
② If the malfunctions corresponding to more
than 2 trouble codes can be determined, after
the trouble codes are deleted (erasable trouble
codes), drive the vehicle to above 40km/h to
determine the malfunctions to that the trouble
codes correspond and check in accordance
with the registered trouble codes (determine
the same one trouble code).
Troubleshooting
Flow
Replace sensor
Replace HECU
Is problem
still present?
Checking
complete
Yes
No
Page 20 of 38
Table 3
Trouble Code
C1 201(12) C1 204(22)
C1 207(32) C1 210(42)
Possible Cause
Interference of gear ring or sensor:
Occurred when installed with non-
standard specification gear rings.
Note: ① The sensor signal is not uniform
when the gears are adhered with engine oil
and the impurities such as slag;
② The air gap refers to the air gap between
the gear ring and the sensor;
③ If the malfunctions corresponding to more
than 2 trouble codes can be determined, after
the trouble codes are deleted (erasable trouble
codes), drive the vehicle to above 40km/h to
determine the malfunctions to that the trouble
codes correspond and check in accordance
with the registered trouble codes (determine
the same one trouble code).
Troubleshooting
Flow
Replace sensor
Replace HECU
Is problem
still present?
Checking complete
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст