Chery QQ6 (S21) / S12LHD. Manual — part 124
Page 21 of 38
Table 4
Trouble
Code
C1 101(51) C1 102(52)
Possible
Cause
Abnormal battery voltage:
Occurred when the voltage is too high or too
low
Note: If the malfunctions corresponding to more
than 2 trouble codes can be determined, after the
trouble codes are deleted (erasable trouble codes),
drive the vehicle to above 40km/h to determine the
malfunctions to that the trouble codes correspond
and check in accordance with the registered
trouble codes (determine the same one trouble
code).
T
ro
u
b
le
sh
o
o
ti
ng
F
low
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Adjust connector pins
Correctly
assemble
connectors
Replace HECU
Replace AC
generator
Is below 9.4V?
Is above 17V?
Is status good?
Is status good?
Is between
9.4V~17V?
Check and
replace wiring
Is below 1Ω?
Check and replace
battery
Adjust
status
of
grounding terminal
① Measure the voltage
between battery terminal
(+) and (-)
Remove
harness
side
connector and measure the
voltage between pin 4 (+) and
8(-) and between pin 4(+) and
24(-) when the entire vehicle
circuits are on.
Measure the resistance
between the harness side
connector pin 4(+) and
battery (+) terminal
Confirm
the
assembling
status and pin displacement
of harness side connector pin
4, 8, and 24
Confirm
and
check
grounding status of harness
side connector pin 8 (-),
and 24 (+)
Measure the voltage between
pin 4 (+) and 8(-) and
between pin 4(+) and 24(-)
when the entire
vehicle
circuits are on.
Re-check from
item ①
Page 22 of 38
Table 5
Trouble Code
C2 402(55)
Possible Cause
Malfunction of motor fuse/motor
Note: If the malfunctions corresponding to more
than 2 trouble codes can be determined, after the
trouble codes are deleted (erasable trouble codes),
drive the vehicle to above 40km/h to determine
the malfunctions to that the trouble codes
correspond and check in accordance with the
registered trouble codes (determine the same one
trouble code).
Troubleshooting
Flow
(1) After the harness side
connector is removed, confirm
if the harness side pin 25 and
the
grounding
wire
are
connected
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Is status good?
Is status good?
Is it on?
Is it on?
Replace HECU
Is fuse (30A)
normal?
Confirm if the valve fuse
(30A) in the fuse box is
broken
Re-check from item ①
Is forced drive good?
Forced
drive the
HECU with
diagnosis instrument (valve relay and
motor start)
Adjust the connector pins and
correctly assemble connector
Confirm the assembling status and
pin displacement of pin 25 of
harness side connector
Check and replace the valve fuse
Check and replace the wiring of
harness side pin 25
Check and replace
the wiring of harness
side pin 25.
Confirm if the harness side
pin 25 and the terminal in the
fuse box are connected
Page 23 of 38
Table 6
Trouble Code
C2 112(54)
Possible Cause
Malfunction of valve fuse and relay:
a) Broken of primary relay or fuse
b) Short-circuit of primary relay
Note: If the malfunctions corresponding to more
than 2 trouble codes can be determined, after the
trouble codes are deleted (erasable trouble codes),
drive the vehicle to above 40km/h to determine
the malfunctions to that the trouble codes
correspond and check in accordance with the
registered trouble codes (determine the same one
trouble code).
Troubleshooting
Flow
(1) After the harness side
connector is removed, confirm
if the harness side pin 25 and
the
grounding
wire
are
connected
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Is status good?
Is it on?
Is it on?
Replace HECU
Is fuse (30A)
normal?
Confirm if the valve fuse
(30A) in the fuse box is
broken
Re-check from item ①
Is forced drive good?
Forced drive the HECU with
diagnosis instrument (valve
relay and motor start)
Adjust the connector pins and
correctly assemble connector
Confirm the assembling status and
pin displacement of pin 25 of
harness side connector
Check and replace the valve
fuse
Check and replace the wiring of
harness side pin 25
Check and replace
the wiring of harness
side pin 25.
Confirm if the harness side
pin 25 and the terminal in the
fuse box are connected
Page 24 of 38
Table 7
Trouble Code
C1 604(53)
Possible Cause
Malfunction of ECU internal circuit
and valve coil
Note: If the malfunctions corresponding to
more than 2 trouble codes can be determined,
after the trouble codes are deleted (erasable
trouble codes), drive the vehicle to above
40km/h to determine the malfunctions to that
the trouble codes correspond and check in
accordance with the registered trouble codes
(determine the same one trouble code).
Troubleshooting
Flow
Yes
No
Replace HECU
Is it below 1Ω?
Confirm and check the grounding
status between the harness side
connector pin 8(-) and 24(1)
grounding terminal.
Remove the harness side connector and measure
the resistance between the harness side connector
pin 8 (-) and grounding wire and between the pin
24 (-) and grounding wire
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст