Chery QQ6 (S21) / S12LHD. Manual — part 213
No
Replace
fuel
pressure regulator
Yes
Next step
14
When engine coolant is at low temperature, pull
out electronic throttle body on harness and
observe if engine revolution will rise.
No
Check
electronic
throttle body for
damage
Yes
Next step
15
Put the ignition switch to “ON”. Check if
voltage on the following pins of ECU is normal:
if it is a battery voltage around 12V on 12#, 14#,
15# pins; if the voltage between 51#, 53#, 3#,
61#, 80# pins and the wire is zero.
No
Check wires and
plugs
Yes
Next step
16
Check if ignition advance angle is normal.
No
Check
other
systems
Yes
Next step
17
Check if cylinder compression pressure of
engine is normal, if low, add a little engine oil
into each cylinder and re-measure if the cylinder
pressure is normal.
No
Troubleshooting
Yes
Repair or replace
18
If air cleaner or airflow sensor is choked.
No
Next step
Yes
Replace ECU
19
Check if the coolant temperature sensor is
working correctly.
No
Repair or replace
Note: Note if theft-proof system has started up. After theft-proof system has started up,
when starting the engine, the staring motor can run normally, but the engine can not
start; therefore, please note if this system can work normally.
12.6 Cold Starting Difficulty
No.
Operating steps
Result
Follow up steps
Yes
Remove the failure
displayed
1
Put the ignition switch to “ON”. Use a failure
diagnostic tester to check if any failure
information record exists.
No
Next step
Yes
Next step
2
Use a multimeter to check if the coolant
temperature sensor is normal. (A 2.8KΩ electric
resistance can also be connected in series between
39# and 17# pins of ECU to start the engine in
stead of the coolant temperature sensor. If the
engine can start, it indicates off normal of coolant
temperature sensor.)
No
Replace the sensor
Yes
Next step
3
Put the ignition switch to “ON”. Check if voltage
on the following pins of ECU is normal: if it is a
battery voltage around 12V on 12#, 14#, 15# pins;
if the voltage between 51#, 53#, 3#, 61#, 80# pins
and the wire is zero.
No
Check wires and
plugs
Yes
Next step
4
Check the air cleaner and look if it is open.
No
Replace
Yes
Next step
5
After starting successfully, check if air intake
consumption of the engine at idle speed is around
300Kg/h (remember to check if cylinder pressure
is normal).
No
Eliminate
the
leakage failure of
air intake system
Yes
Check
the
electronic throttle
6
Step on the throttle slightly and observe if it is
easy to be started easily.
No
Next step
Yes
Next step
7
When engine coolant is at low temperature, pull
out electronic throttle body joint on harness and
observe if engine revolution will rise.
No
Check the electric
throttle body
Yes
Next step
8
Connect fuel manometer valve. Let 86# pin of fuel
pump relay directly ground. Turn on ignition
switch to make fuel pump relay and fuel pump
work, and then check if fuel pressure is at around
400kPa.
No
12
Yes
11
9
Use a special joint to directly provide a 12V
electricity and ground wire from battery to injector
and check if the injector works normally.
No
Next step
Yes
Next step
10
Clean out the fuel injector and look if it can work
correctly.
No
Replace
fuel
injector
11
Check if fuel is deteroprated or moisture.
Yes
Replace fuel
No
17
Yes
Next step
12
Check if the fuel pressure value is below 300 kPa.
No
16
Yes
Next step
13
Close the fuel manometer valve. Re-engage the
ignition switch to let the fuel pump run for a
period of time, and then check if fuel pressure can
be built up.
No
15
Yes
Check fuel pressure
regulator and fuel
pump
14
Open the valve of fuel gauge and clamp the oil
return pipe by oil return baffle so that the oil can
not return. Check if the oil pressure occurs
immediately.
No
Repair and replace
fuel injector and oil
pipe
Yes
Repair or replace
oil intake pipe
15
Check if the oil intake pipe is leaky or jammed.
No
Replace oil pump
Yes
Repair or replace
oil return pipe
16
Check if the oil return pipe is bended or jammed.
No
Replace
fuel
pressure regulator
or fuel pump
Yes
Next step
17
Check if the pressure of cylinder is normal.
No
Troubleshooting
Yes
Repair
18
Check if the engine air intake system is leaky.
No
Next step
Yes
Repair or replace
19
If air cleaner or airflow sensor is choked.
No
Replace ECU
Note: The cold starting problem relates to more failure points, among which water
temperature sensor is comparatively important, because it is the major parameter for
determination of injection pulse-width when starting the engine. In case of a water
temperature sensor failure or it generates a false signal, the system can not judge the
temperature and starting difficulty may occur.
12.7 Unsteady Idle Speed at Any Time
Yes
Remove the failure
displayed
1
Put the ignition switch to “ON”. Use a failure
diagnostic tester to check if any failure
information record exists.
No
Next step
Yes
Repair or replace
the
electronic
throttle
2
Check if electronic throttle system of engine
works normally.
No
Next step
Yes
Check wires and
plugs
3
Turn on ignition switch, connect an adaptor
between ECU and harness, and then check if the
voltage between 17# and 42# pins of ECU,
between 39# and 17# pins of ECU (signal output
terminal of intake air temperature sensor and
coolant temperature sensor) as well as 64#, 65#,
66#, 67# pins of ECU (for control of DC motor) is
normal.
No
Next step
Yes
8
4
Let engine run at idle speed, spark out cylinder in
turn, and observe if engine revolution will fall and
fluctuate (cut fuel to injector).
No
Next step
Yes
Next step
5
Check the fuel injectors of each cylinder and look
if they are in right conditions.
No
Check fuel injector
and wires
Yes
Next step
6
Check if resistance value of ignition cable of each
cylinder is normal (can not exceed 16kΩ).
No
Replace
Yes
Maintain
7
Check if ignition system works normally.
No
Next step
Yes
Next step
8
Check if the spark plug is in right conditions.
No
Replace spark plug
Yes
Next step
9
Connect fuel manometer valve. Short 30# and 87#
pins of fuel pump relay to make the fuel pump
run, and then check if fuel pressure is around
400kPa.
No
13
Yes
12
10
Use a special joint to directly provide a 12V
power supply and intermittent ground wire signal
from battery to injector and check if the injector
can work intermittently.
No
Next step
Yes
Next step
11
Clean out the fuel injector and look if it can work
correctly.
No
Replace
fuel
injector
Yes
Replace fuel
12
Check if fuel is deteroprated or moisture.
No
18
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст