Chery A15. Manual — part 38
Diagnostic trouble code: P0335 “Signal malfunction of crankshaft position
sensor”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“OFF” position.
Proceed to next step.
Yes
Proceed to next step.
2
Disconnect the connector of rotary
sensor on the wiring harness, inspect
with multimeter to verify that the
resistance between 2# pin and 3# pin of
this rotary sensor is about 770~950Ω
under 20 .
℃
No
Replace the sensor.
Yes
Repair or replace the
wiring harness.
3
Verify that the circuits between 2# and
3# pin of the rotary sensor connector
and 34# and 15# pins of ECU are open,
or are short to ground or power supply.
No
Proceed to next step.
Yes
Refer to diagnosis
help.
4
Verify that the signal panel of flywheel
is in good condition.
No
Replace the signal
panel.
G-40
Diagnostic trouble code: P0336 “Malfunction of improper signal of crankshaft
position sensor”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“OFF” position.
Proceed to next step.
Yes
Proceed to next step.
2
Disconnect the connector of rotary
sensor on the wiring harness, inspect
with multimeter to verify that the
resistance between 2# pin and 3# pin of
this rotary sensor is about 770~950Ω
under 20 .
℃
No
Replace the sensor.
Yes
Repair and replace
the wiring harness.
3
Verify that the circuits between 2# and
3# pin of the rotary sensor connector and
34# and 15# pins of ECU are open, or are
short to ground or power supply.
No
Proceed to next step.
Yes
Refer to diagnosis
help.
4
Verify that the signal panel of flywheel is
in good condition.
No
Replace the signal
panel.
G-41
Diagnostic trouble code: P0340 “Malfunction of phase angle sensor signal”
Item
No.
Operation procedure
Inspection
results
Follow-up
procedure
1
Connect the diagnostic tester and adaptor,
and turn the ignition switch to “ON”
position.
Proceed to next
step.
Yes
Proceed to Step 4
2
Disconnect the connector of phase angle
sensor on the wiring harness, inspect with
multimeter to verify that the voltage
between 1# pin and 3# pin of this phase
angle sensor connector is about 12V.
No
Proceed to next
step.
Yes
Repair or replace
the wiring
harness.
3
Verify that the circuit between 3# pin of
phase angle sensor and 87# pin of the main
relay is open or short to ground;
Verify that 1# pin of phase angle sensor is
grounded properly.
No
Proceed to next
step.
Yes
Proceed to Step 6
4
Verify that the voltage between 2# pin of
the phase angle sensor connector and the
negative grid of power supply is about 9.9V.
No
Proceed to next
step.
Yes
Repair or replace
the wiring
harness.
5
Verify that the circuit between 2# pin of the
phase angle sensor connector and 79# pin of
ECU is open, or is short to ground or power
supply.
No
Proceed to next
step.
Yes
Refer to diagnosis
help.
6
Verify that the signal panel of camshaft is in
good condition.
No
Replace the signal
panel.
G-42
Diagnostic trouble code: P0443 “Malfunction in control circuit of drive stage of
carbon canister control valve”
Item
No.
Operation procedure
Inspection
results
Follow-up
procedure
1
Connect the diagnostic tester and adaptor, and
turn the ignition switch to “ON” position.
Proceed to next
step.
Yes
Proceed to Step
4
2
Disconnect the connector of carbon canister
control valve on the wiring harness, inspect
with multimeter to verify that the voltage
between 1# pin of this connector and the
negative grid of power supply is about 12V.
No
Proceed to next
step.
Yes
Repair or
replace the
wiring harness.
3
Verify that the power supply circuit of carbon
canister control valve is open or short to
ground.
No
Proceed to Step
2
Yes
Proceed to next
step.
4
Inspect with multimeter to verify that the
resistance between 1# and 2# pins of carbon
canister control valve is within 22-30Ω under
20 .
℃
No
Replace the
control valve.
Yes
Refer to
diagnosis help.
5
Inspect with multimeter to verify that the
voltage between 1# pin of carbon canister
control valve connector and the negative grid
of power supply is about 3.7V.
No
Proceed to next
step.
Yes
Repair or
replace the
wiring harness.
6
Verify that the circuit between 2# pin of
carbon canister control valve connector and
46# pin of ECU is open.
No
Refer to
diagnosis help.
G-43
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст