Chery A15. Manual — part 39
Diagnostic trouble code: P0444 “Undervoltage in control circuit of drive stage of
carbon canister control valve”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“ON” position.
Proceed to next step.
Yes
Proceed to Step 4
2
Disconnect the connector of carbon
canister control valve on the wiring
harness, inspect with multimeter to
verify that the voltage between 1# pin
of this connector and the negative grid
of power supply is about 12V.
No
Proceed to next step.
Yes
Repair or replace the
wiring harness.
3
Verify that the power supply circuit of
carbon canister control valve is open
or short to ground.
No
Proceed to Step 2
Yes
Proceed to next step.
4
Inspect with multimeter to verify that
the resistance between 1# and 2# pins
of carbon canister control valve is
within 22-30Ω under 20 .
℃
No
Replace the control
valve.
Yes
Refer to diagnosis
help.
5
Inspect with multimeter to verify that
the voltage between 1# pin of carbon
canister control valve connector and
the negative grid of power supply is
about 3.7V.
No
Proceed to next step.
Yes
Repair or replace the
wiring harness.
6
Verify that the circuit between 2# pin
of carbon canister control valve
connector and 46# pin of ECU is short
to ground.
No
Refer to diagnosis
help.
G-44
Diagnostic trouble code: P0445 “Overvoltage in control circuit of drive stage of
carbon canister control valve”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“ON” position.
Proceed to next step.
Yes
Proceed to Step 4
2
Disconnect the connector of carbon
canister control valve on the wiring
harness, inspect with multimeter to
verify that the voltage between 1# pin
of this connector and the negative grid
of power supply is about 12V.
No
Proceed to next step.
Yes
Repair and replace the
wiring harness.
3
Verify that the power supply circuit of
carbon canister control valve is open or
short to ground.
No
Proceed to Step 2
Yes
Proceed to next step.
4
Inspect with multimeter to verify that
the resistance between 1# and 2# pins
of carbon canister control valve is
within 22-30Ω under 20 .
℃
No
Replace the control
valve.
Yes
Refer to diagnosis
help.
5
Inspect with multimeter to verify that
the voltage between 1# pin of carbon
canister control valve connector and
the negative grid of power supply is
about 3.7V.
No
Proceed to next step.
Yes
Repair or replace the
wiring harness.
6
Verify that the circuit between 2# pin
of carbon canister control valve
connector and 46# pin of ECU is short
to power supply.
No
Refer to diagnosis
help.
G-45
Diagnostic trouble code: P0480 “Malfunction in control circuit of relay of A/C
condenser fan A”
Item
No.
Operation procedure
Inspection
results
Follow-up procedure
1
Connect the diagnostic tester and
adaptor, and turn the ignition switch to
“OFF” position.
Proceed to next step.
Yes
Proceed to Step 4
2
Pull out the relay of A/C condenser
fan, turn the ignition switch to “ON”
position and verify that the voltage
between the power supply terminal of
the relay (i.e. 30# and 85# pins of the
relay) and the negative grid of power
supply is about 12V.
No
Proceed to next step.
Yes
Repair or replace the
wiring harness.
3
Verify that the power supply circuit of
the relay of A/C condenser fan is open
or short to ground.
No
Proceed to Step 2
Yes
Replace the relay.
4
Inspect with multimeter to verify that
the voltage between the control
terminal of relay of A/C condenser fan
(i.e. 86# pin of the relay) and the
negative grid of power supply is about
3.7V.
No
Proceed to next step.
Yes
Repair or replace the
wiring harness.
5
Verify that the circuit between the
control terminal of relay (i.e. 86# pin
of the relay) and 50# pin of ECU is
open, or is short to power supply or to
ground.
No
Refer to diagnosis
help.
G-46
Diagnostic trouble code: P0481 “Malfunction in control circuit of relay of A/C
condenser fan B”
Item
No.
Operation procedure
Inspection
results
Follow-up
procedure
1
Connect the diagnostic tester and adaptor,
and turn the ignition switch to “OFF”
position.
Proceed to next
step.
Yes
Proceed to Step 4
2
Pull out the relay of A/C condenser fan,
turn the ignition switch to “ON” position
and verify that the voltage between the
power supply terminal of the relay (i.e.
30# and 85# pins of the relay) and the
negative grid of power supply is about
12V.
No
Proceed to next
step.
Yes
Repair or replace
the wiring harness.
3
Verify that the power supply circuit of the
relay of A/C condenser fan is open or short
to ground.
No
Proceed to Step 2
Yes
Replace the relay.
4
Inspect with multimeter to verify that the
voltage between the control terminal of
relay of A/C condenser fan (i.e. 86# pin of
the relay) and the negative grid of power
supply is about 3.7V.
No
Proceed to next
step.
Yes
Repair or replace
the wiring harness.
5
Verify that the circuit between the control
terminal of relay (i.e. 86# pin of the relay)
and 68# pin of ECU is open or is short to
power supply or to ground.
No
Refer to diagnosis
help.
G-47
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст